background image

TB MRU3-1 12.00 E

3

1

Introduction and application

The voltage supervision relay 

MRU3-1 

protects electri-

cal power generators, consumers or operating com-
ponents generally against over- or undervoltages.

Among other applications the relay can be used:

 

for detection of over- or undervoltages in power gen-
rating plants and energy supply systems

 

to protect generators against critical overvoltages in
case of defective voltage regulators

 

as undervoltage protection for motors

 

as generator stator earth fault protection

 

as over- and undervoltage protection with evaluating
the symmetrical components (

MRU1-2

, detailed in-

formation on this type can be found in the relevant
technical description)

There is also a similar protection relay 

IRU1

 available

in a more simpler design, i.e. with less function, with-
out display and without serial interface.

Important:

For additional common data of all 

MR

-relays please

refer to technical description "

MR

 - Digital Multifunc-

tional Relays".

2

Features and characteristics

 

Microprocessor technology with watchdog,

 

digital filtering of the measured values by using dis-
crete Fourier analysis to suppress higher harmonics
and d.c. components induced by faults or system
operations,

 

two parameter sets,

 

voltage supervision each with two step under-/ and
overvoltage detection,

 

Completely independent time settings for voltage su-
pervision

 

display of all measuring values and setting parame-
ters for normal operation as well as tripping via a
alphanumerical display and LEDs,

 

display of measuring values as primary quantities

 

1-phase or 3-phase tripping criterion for the U</U>
step,

 

Storage and display of tripping values in a fault
memory (voltage-failure safe),

 

recording of up to eight fault occurences with time
stamp

 

for blocking the individual functions by the external
blocking input, parameters can be set according to
requirement,

 

suppression of indication after an activation
(LED flash),

 

free assignment for output relays,

 

display of date and time,

 

in complience with VDE 0435, part 303 and IEC
255,

 

serial data exchange via RS485 interface possible;
alternatively with SEG RS485 Pro-Open Data Proto-
col or Modbus Protocol.

Содержание MRU3-1



























Отзывы: