Seenergy Dandy, Инструкция пользователя

Страница: 12 / 56

- 12 -
USE AND MAINTENANCE
•
We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air. The effective
performance of the cooker hood depends on constant main-
tenance; the anti-grease filter and the active carbon filter both
require special attention.
• The anti-grease filter is responsible retaining the grease
particles suspended in the air, therefore it is subject to clogging
with variable frequency according to the use of the appliance.
- To prevent the danger of possible fires, at least every 2
months one must wash the anti-grease filters by hand using
non-abrasive neutral liquid detergents or in the dishwasher
at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
• The active carbon filters are used to purify the air that is
sent back into the room and its function is to mitigate the
unpleasant odours produced by cooking.
- The non-regenerable active carbon filters must be replaced
at least every 4 months. The saturation of the active charcoal
depends on the more or less prolonged use of the appliance,
on the type of kitchen and on the frequency with which anti-
grease filter is cleaned.
- Regenerable active charcoal filters must be washed by hand,
with non abrasive neutral detergents, or in the dishwasher at
a maximum temperature of 65°C (the washing cycle must be
complete without dishware). Remove excess water without
damaging the filter, remove the plastic parts, and let the
mat dry in the oven for at least 15 minutes approximately at
a maximum temperature of 100°C. To keep the regenerable
charcoal filter functioning efficient this operation must be
repeated every 2 months. These must be replaced at least
every 3 years or when the mat is damaged.
• Before remounting the anti-grease filters and the regen -
erable active charcoal filters it is important that they are
completely dry.
• Clean the hood frequently, both internally and externally,
using a cloth dampened with denatured alcohol or neutral
liquid detergents that are non abrasive.
•
The lighting .system is designed for use during cooking
and not for the prolonged general lighting of the room. The
prolonged use of the lighting system significantly decreases
the average duration of the bulbs.
• If the appliance is equipped with courtesy lights it is possible
to use them for general room lighting for a prolonged amount
of time.
• Attention: the non compliance with the hood cleaning
warnings and with the replacement and cleaning of the filters
entails risk of fires. One therefore recommends keeping to the
suggested instructions.
• Replacing halogen light bulbs (Fig.11A):
To replace the halogen light bulbs
B
, remove the glass pane
C using a lever action on the relevant cracks. Replace the bulbs
with new ones of the same type.
Caution:
do not touch the
light bulb with bare hands.
• Replacing LED lamps (Fig.11B):
If the appliance version is with LED lamps, the intervention of
a specialised technician is necessary to replace them.
• Commands (Fig.12):
Push-button A = On/off lights switch.
Push-button B =
On/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off.
Decreases the motor speed.
Display C = Indicates the motor speed level selected and
activates the timer.
Push-button D = Switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 6’, then the appliance go back to work at the
original speed. During this function the display blinks.
Key E =
The Timer times the functions on activation for 15
minutes, after which they are switched off. The Timer is deac-
tivated by re-pressing Key E .
When the Timer is activated the decimal point must flash on
the display. The Timer cannot be activated if the intensive
speed is functioning.
The “ clean air ” function is activated by pressing key E for 2
seconds when the appliance is switched off. This switches the
motor on for 10 minutes every hour at the first speed.
During functioning a rotary movement of the peripheral seg-
ments must be visualised on the display. When this time has
passed the motor switches off and the fixed letter “ C ” must
be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on.
Press any key apart from the light keys to return to normal
functioning. Press key E to deactivate the function.
• Anti-grease/active charcoal filters saturation:
- When display item C flashes, at a speed where it alternates
with the letter
F
(e.g.
1
and
F
), the anti-grease filters must be
washed.
- When display item C flashes, at a speed where it alternates
with the letter
A
(e.g.
1
and
A
), the active carbon filters must
be replaced or washed depending on the type of filter.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds , until the indication F or A shown
on the display
C
stops flashing.
- If the display C does not stop flashing, repeat the operation
with the motor on.
• Commands (Fig.13):
NOTE:
with this command it is also possible to control the ap-
pliance using a remote control, to be requested as an accessory.
A Button
= Switches the hood on/off. The equipment switches
on at the 1st speed.
B Button = Decreases motor speed.
C Display
= Shows the selected motor speed and timer acti-
vation/intense speed/filter warning.
D Button
= Increases motor speed.
Pressing the 4th speed button engages the intense function
for 6 minutes, then the equipment goes back to working at
the speed at which it was activated. During this function, the
number 4 flashes on the display.
- If you wish to deactivate the function before the 6 minutes,
press the B button.
Attention! Some models only work up to the 3rd speed and,
therefore, do not have the intense function.
E Button = Pressing this button activates the Timer function