26
Remote Thermostat Control
(remote control)
AUTO
COOL
PM
FAN
SPEED
ECONOMY
REMOTE CONTROL
ILL239-D
SENSOR
TOUCH
LOCATING THE REMOTE CONTROL
INSTALLING THE RECEIVER
The following section
describes installation of the receiver,
which requires positioning of the
receiver external to the cooler, inside
the attic or below the ceiling. The
supplied receiver lead is 16
’
(5.0m)
long, sufficient to reach into the attic
or below the ceiling, from the cooler
electronic module.
The remote control should be placed
approximately 5 feet (1.5 meters)
above the floor, in the most used room
in the home. This will give the optimum
temperature sensing and operating
position for the user.
:
•
Avoid direct sunlight exposure.
•
Avoid mounting on external walls.
•
Avoid mounting the remote control
near heat sources such as stoves
and televisions.
•
Do not locate in the direct airflow of
the duct outlets.
•
Do not locate in strong drafts or in
dead spots such as cupboards /
drawers.
Placement is critical for correct
functioning of the thermostat
(incorporated in the remote control).
The following points must be taken into
consideration
Note:
Running the Receiver Cable
Aim to secure the receiver away from
the ductwork, but as near as possible to
the location of the remote control.
Other Options for Mounting Receiver
Signal Problems
Flat Roof Installation
Plug the receiver cable to point Fig 22
“
Receiver
”
on the electronic controller. Run
the cable to the attic space or below the
ceiling to the receiver location and plug the 6
pin end (with sticker) to the receiver. (Fig 30)
For installations where the roof is framed in
steel, position the receiver between the
metal joists keeping the antenna as far away
from metal joists as possible and directing
the antenna perpendicular (right angle) to
the joists will give the best results.
For most installations, mounting the receiver
to the roof rafter as shown (Fig 29) will
provide satisfactory performance.
The standard installation arrangement will
satisfy the majority of applications.
However you may find difficult cases as
follows:
For signal problems in houses with a metal
roof, position the receiver as close as
possible to the metal roof with the antenna
pointing directly away from the roof (Fig 29).
Where the installation is on a building with a
flat roof and the attic space is less than 4
’
(1.2 meters) deep, alternative mounting
locations may need to be found for the
receiver.
For example, install the receiver below the
ceiling in the top of a nearby cupboard.
Do not wrap any excess receiver cable
around the receiver. Do not extend the
receiver cable.
28
16’
SENSOR
TOUCH
Remote Control
ILL665-D
AUTO
COOL
PM
FAN
SPEED
ECONOMY
REMOTE CONTROL
A = Metal Roofing.
B = Wood or Metal Beam.
C = Receiver (Mount as close as
possible to the metal roof).
A = The 6 pin plug (the end with the
"RECEIVER" sticker attached)
connects into the socket on the
underside of the receiver.
30
Important:
The orientation and position of the
receiver may affect the receiver's
performance. Other factors that may
also influence performance are:
(1)..Shielding from metal in the attic
lying between the receiver and
Remote Control. This may include
Sisalation/sarking (foil sheets),
and ductwork.
(2)..Reflections from metal around the
receiver.
(3)..Interference from nearby
transmitters (e.g. mobile phone, AM
radio, Television, RF security
systems).
29
SETTING THE ADDRESS CODE
within 4 minutes after turning on
the main power at the electronics
module.
The Breezair electronics module will
automatically recognize the remote
control connection, provided the
address code has been correctly set.
This is simply achieved by fitting the
batteries into the remote control
The screen will stay blank for
5 seconds then display
“
Id
”
for 1
second. The communication address
code will take a few seconds to set,
then the remote control can be turned
on. (Fig. 31)
If communication cannot be achieved,
the power to the cooler will need to be
turned off, and the batteries need to
be removed from the remote control.
Wait until the screen goes completely
blank, then repeat the above
procedure.
31
27
SEELEY INTERNATIONAL –
INSTALLATION & OPERATION MANUAL
16
SENSOR
T
OUCH
Remote Control
1. Fix the top screw
to the wall,
without
tightening
completely.
2. Fix the second
screw through
the lower oval
hole, without
tightening
completely.
3. Straighten and
align the
mounting
bracket, tighten
screws to hold
the bracket in it
’
s
correct position.
