Security Chimneys International SECURE HE43-1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 30

background image

15

I

NSTALLATION OF THE FAN KIT MODEL

UZY5

Note: This fan kit can easily be installed when the fireplace has a pre-installed junction box.
You just have to plug them in..

Rating: 120 Volts, 60Hz, .63A.

The fans have magnetic blower mounts. The junction box (factory installed on approved fireplaces for
the use of this fan kit) must be connected to 110 VAC service before permanently enclosing the fireplace.
The access hole for connecting the 110 VAC is located on the lower right exterior side of the fireplace.

I

NSTALLATION INSTRUCTIONS

:

1.

Open the bottom louver of the fireplace.

2.

Place each fan kit into the fireplace side opening 1" from the back of the fireplace.

3.

Install the automatic fan activator on the side of the firebox (the fan activator has a magnetic mount).

4.

Plug the fan kit into the junction box.

5.

Ground both fans to the back panel using the green screws.

NOTE: The fireplace must be electrically connected and grounded in accordance with local codes

or in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code.
For U.S.A. installations, follow local codes and the National Electrical Code ANSI/NFPA
No 70.

CAUTION: Should this fan require servicing, the power supply must be disconnected.

These fans do not need regular maintenance; however, periodic cleaning is required. Check the area in
front of the fans and wipe or vacuum at least once a month during the operating season.

«
...
13
14
15
16
17
...
»

Содержание SECURE HE43-1































Отзывы:

Нет отзывов

Похожие инструкции для SECURE HE43-1

Бренд: HAMPTON BAY Страницы: 10

Бренд: Martin Страницы: 36

Бренд: Uniflame Страницы: 8

Бренд: Jøtul Страницы: 72

Бренд: Majestic Страницы: 20

Бренд: Woodbridge Fireplace Inc Страницы: 36

Бренд: Home Decorators Collection Страницы: 20

Бренд: Yosemite Страницы: 15

Бренд: Lamborghini Caloreclima Страницы: 116

Бренд: Warmlite Страницы: 12

Бренд: Royal Страницы: 17

Бренд: Royal Страницы: 52

BarcelonaLights36ZEN

Бренд: IHP Страницы: 40

Бренд: Waterford Страницы: 24

Бренд: Heat Surge Страницы: 21

Бренд: Northwest Страницы: 7

Бренд: GRAND EFFECTS Страницы: 11

Бренд: Dik Geurts Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды