background image

29

1. Press and release the purple “learn”

button on motor unit. The learn
indicator light will glow steadily for 30
seconds.

2. Within 30 seconds, enter a four digit

personal identification number (PIN)
of your choice on the keypad. Then
press and hold the ENTER button.

3. Release the button when the motor

unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.

To Add, Reprogram or Change a Keyless Entry PIN

NOTE:

Your new Keyless Entry must be programmed to operate your garage door opener.

USING THE “LEARN” BUTTON

USING THE  SMART  CONTROL  PANEL™

LOCK

L

I

GHT

To change an existing, known PIN

If the existing PIN is known, it may be changed by one
person without using a ladder.

1. Press the four buttons for the present PIN, then press and

hold the # button.

The opener light will blink twice. Release the # button.

2. Press the new 4-digit PIN you have chosen, then

press Enter.

The motor unit lights will blink once when the PIN has been
learned.

Test by pressing the new PIN, then press Enter. The door
should move.

To set a temporary PIN

You may authorize access by visitors or service people with a
temporary 4-digit PIN. After a programmed number of hours
or number of accesses, this temporary PIN expires and will
no longer open the door. It can be used to 

close

the door

even after it has expired. To set a temporary PIN:

1. Press the four buttons for your personal entry PIN (not the

last temporary PIN), then press and hold the 

button.

The opener light will blink three times. Release the button.

2. Press the temporary 4-digit PIN you have chosen, then

press Enter.

The opener light will blink four times.

3. To set the number of 

hours

this temporary PIN will work,

press the number of hours (up to 255), then press

.

OR

3. To set the number of 

times

this temporary PIN will open

door, press the number of times (up to 255), then press #.

The opener light will blink once when the temporary PIN has
been learned.

Test by pressing the four buttons for the temporary PIN, then
press Enter. The door should move. If the temporary PIN was
set to a certain number of openings, remember that the test
has used up one opening.To clear the temporary password,
repeat steps 1-3, setting the number of hours or times to 0 in
step 3.

One Button Close:

Opener can be closed by pressing only

the ENTER button if the one button close feature has been
activated. This feature has been activated at the factory. To
activate or deactivate this feature press and hold buttons 1
and 9 for 10 seconds. The keypad will blink twice when the
one button close is active. The keypad will blink four times
when one button close is deactivated.

LOC

K

LIGHT

1. Press the Prog <Learn> button on the

Smart Control Panel™.

2. Press the Prog <Learn> button again

to confirm Learn Mode.

3. Enter a four digit personal

identification number (PIN) of your
choice on the keypad. Then press
enter.

4. When the motor unit lights blink, it

has learned the code. If light bulbs
are not installed, two clicks will be
heard.

NOTE:

This method requires two people if the Keyless

Entry is already mounted outside the garage.

LOCK

LIGH

T

LOCK

LIGH

T

Содержание Elite 3800P





































Отзывы: