Seco SBC-C90 Скачать руководство пользователя страница 54

Страница: 54 / 63

SBC-C90

4.3.19

M.2 peripheral management submenu

4.3.20

Network Stack configuration submenu

4.3.21

AMD CBS submenu

Disable (default) or enable 120 Ohm Rx termination.

Tx Termination

Disabled / Enabled

Option available when selecting RS-422 mode.
Disable (default) or enable 120 Ohm Tx termination.

Menu Item

Options

Description

M.2 Key E

Options available for devices on M.2 Key E

Wifi on M.2

Disabled / Enabled

Enable Wifi capabilities from Wifi M.2 card

Bluetooth on M.2

Disabled / Enabled

Enable bluetooth capabilities from bluetooth M.2 card .

M.2 Key B

Options available for devices on M.2 Key B

WWAN on M.2

Disabled / Enabled

Enable WWAN capabilities from a WWAN M.2 card

Menu Item

Options

Description

Network Stack

Enabled / Disabled

Enables or disables UEFI Network Stack. When enabled, following menu items will appear

Ipv4 PXE Support

Enabled / Disabled

Enables or disables IPV4 PXE Boot Support. If disabled, IPV4 PXE boot option will not be created

Ipv4 HTTP Support

Enabled / Disabled

Enables or disables IPV4 HTTP Boot Support. If disabled, IPV4 HTTP boot option will not be created

Ipv6 PXE Support

Enabled / Disabled

Enables or disables IPV6 PXE Boot Support. If disabled, Ipv6 PXE boot option will not be created

Ipv6 HTTP Support

Enabled / Disabled

Enables or disables IPV6 HTTP Boot Support. If disabled, Ipv6 HTTP boot option will not be created

IPSEC Certificate

Enabled / Disabled

Enables or disables IPSEC certificate for Ikev

PXE boot wait time

[0..5]

Wait time to press ESC key to abort the PXE boot

Media detect count

[1..50]

Number of times that the presence of media will be checked

Menu Item

Options

Description

NBIO Common options

See submenu

NorthBridge IO Configuration Options

FCH Common options

See submenu

Firmware Controller Hub Configuration options

Содержание SBC-C90































































Результаты поиска

Содержание SBC-C90

Отзывы:

Бренды по названию

Популярные бренды

Seco SBC-C90, Руководство пользователя

Результаты поиска

Содержание SBC-C90

Отзывы:

Бренды по названию

Популярные бренды