SEAWARD Electronic Rigel 266 Plus Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 57

SEAWARD Electronic Rigel 266 Plus Скачать руководство пользователя страница 48

Cleaning the Analyser

46

Chapter 5 Maintaining the Analyser

Cleaning the Analyser

The Analyser case can be cleaned with a damp cloth with, if necessary, a small amount of mild detergent.
Prevent excessive moisture around the socket panel or in the lead storage area.

Do not allow liquid inside the Analyser or near the sockets. Do not use abrasives, solvents or alcohol.

If any liquid is spilt into the Analyser case, the Analyser should be returned for repair, stating the cause of the
defect.

User Maintenance

The Analyser is a rugged quality instrument. However, care should always be taken when using, transporting
and storing this type of equipment. Failure to treat the product with care will reduce both the life of the
instrument and its reliability.

If the Analyser is subject to condensation, allow the Analyser to completely dry before use.

•

Always check the Analyser and all test leads for signs of damage and wear before use.

•

Do not open the Analyser under any circumstances.

•

Keep the instrument clean and dry.

•

Avoid testing in conditions of high electrostatic or electromagnetic fields.

•

Maintenance should only be performed by authorised personnel.

•

There are no user replaceable parts in the Analyser.

•

The unit should be regularly calibrated (at least annually).

For repair or calibration return the instrument to:-

Rigel

Medical

Service Dept.,

Seaward

Electronic

Limited.

Bracken

Hill

South West Industrial Estate

Peterlee,

Co.

Durham

SR8

2SW,

England

Tel : +44 (0)191 586 3511

Fax: +44 (0)191 586 0227

[email protected]

[email protected]

www.seaward.co.uk

www.rigelmedical.com

«
...
46
47
48
49
50
...
»

Содержание Rigel 266 Plus


























































Отзывы:

Нет отзывов