manualshive.com logo in svg

SEAWARD Electronic Primetest 300, Руководство по эксплуатации

Поделиться
Скачать
SEAWARD Electronic Primetest 300 Скачать руководство пользователя страница 28

PrimeTest 300 

 Operating 

Instructions 

 

9.0 Configuration 
 

The configuration facility is used to edit test sequences, 
set time and date and configure Bluetooth connections. 
It is also possible to restore factory settings using this 
function.  
 
The configuration menu is located in the main menu list 
and presents the options shown below.  
 

 

 

9.1  Edit Test Sequences 

 

The PrimeTest 300 is supplied with 17 pre-configured 
test sequences covering a variety of type of electrical 
equipment. The test sequence editor can be used to 
modify test sequences or create new test sequences.  

 

Note:

 

The PrimeTest 300 can store 33 user 

defined test sequences, in addition to the 
17 pre-configured test sequences. 

 

Press 

Menu 

(F4), select 

Edit Test Sequences

 and 

press 

OK 

(F4) to open the 

Edit Test Sequence

 window. 

The 

Options 

(F3) key will display the available options 

as shown below. 
 

- 28 - 

Содержание Primetest 300























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды