If the maximum number of radio controls has been reached and
a programming process started, the control unit will indicate
that it has failed by flashing all the LEDs except the CODE
LED, which will remain lit in a constant manner. After 10 se-
conds the control unit exits programming mode.
2)
SENS. CODE
(Wireless Sensor programming)
Wireless Wind sensor programming:
To programme the Wireless Wind Sensor transmission code,
proceed as follows: Use the SEL button to navigate to a posi-
tion where the SENS. CODE LED flashes; at the same time,
send the Wireless Wind sensor code using the special button
inside the sensor. The SENS. CODE LED will remain lit in a
fixed manner and programming will be complete. If the Wireless
Wind sensor code is not sent within 2 minutes, the control unit
exits programming mode.
Deleting the codes:
To delete the Wireless Wind sensor codes stored in the
memory, proceed as follows: press the SEL button; the SENS.
CODE LED will start to flash. Then press the SET button; the
SENS. CODE LED will switch off and the procedure is com-
plete.
Wireless Wind sensor already stored warning:
If the user attempts to perform the programming procedure for
a Wireless Wind sensor which is already stored in the memory,
the SENS. CODE LED will begin to flash rapidly for a few mo-
ments, to indicate that this procedure cannot be performed; the
unit then returns to the programming stage once again.
Maximum number of Wireless Wind sensors which can be
stored:
If the maximum number of Wireless Wind sensors has been
reached and a programming process started, the control unit
will indicate that it has failed by flashing all the LEDs except the
SENS. CODE LED, which will remain lit in a constant manner.
After 10 seconds the control unit exits programming mode.
Warning indicator:
If there is no communication between the Wireless Wind sensor
and the control unit, after 20 minutes the safety upward move-
ment will be activated automatically. If this lack of communica-
tion persists, further commands will still, nevertheless, result in
the control unit being set to safety mode.
3)
T. MOT.
(Max. Motor Timer programming time 4 minutes)
The control unit comes with a motor power supply time of two
minutes (T. MOT. LED OFF).
The motor running time must be programmed when the shutter
is down, in the following manner:
Press the SEL button until the T. MOT LED flashes, then press
and hold the SET button; the shutter will begin to move up-
wards. Once the desired position has been reached, release
the SET button – at this very moment, the motor running time
will be stored and the T. MOT LED will remain lit.
If you are using an automation which has a stop limit, we re-
commend that you set a time which exceeds the stop limit of
the shutter by a few seconds.
If you want unlimited motor running time, perform the same pro-
gramming procedure, holding down the SET button for less
than two seconds; the T. MOT LED will remain lit and the un-
limited time function will be set. The procedure may be re-
peated if a mistake is made during programming.
4)
WIND SPEED
(Wind Safety threshold programming)
Displaying the programmed Wind threshold:
The Wind Safety threshold may be displayed in the following
way: use the SEL button to navigate to the WIND SPEED LED
position; the LED will double-flash the same number of times as
the stored Wind Safety threshold (each WIND SPEED LED
double-flash corresponds to an increase of 5 km/h), (
for ex
ample: 5 WIND SPEED LED flashes = 25 km/h).
Wind Safety threshold selection from 5 to 40 km/h
The sensor is supplied with a default Wind Safety threshold set-
ting of 25 km/h (WIND SPEED LED OFF).
The Wind Safety threshold may be programmed in the following
way: use the SEL button to navigate to the WIND SPEED LED,
then press the SET button to start the programming procedure:
the WIND SPEED LED will double-flash at the same time (each
WIND SPEED LED double-flash corresponds to an increase of
5 km/h). Press the SET button when the desired threshold has
been reached; at that moment the selected value will be stored
in the memory and the WIND SPEED LED will remain lit (
for
example: 5 WIND LED doubleflashes = 25 km/h).
The procedure may be repeated if a mistake is made during
programming.
EXTENDED MENU 1
The control unit is supplied by the manufacturer with the option
of selecting only the functions listed in the main menu.
To enable the functions of extended menu 1, proceed as fol-
lows: press and hold the SET button for 5 seconds; the T.
MOT. and WIND SPEED LEDs will start flashing alternately.
The user then has 30 seconds in which to select the extended
menu functions using the SEL and SET buttons. After 30
seconds the control unit returns to the main menu.
---------------------- EXTENDED MENU 1 -----------------
Reference LED LED Off LED On
A) CODE remote PGM = OFF remote PGM =
ON
B) SENS. CODE Safety upward mov. =OFF Safety upward mov.
=ON
C) T. MOT. Flashing beacon ON/OFF
D) WIND SPEED Flashing beacon ON/OFF
A) CODE
(Remote programming of radio control):
The control unit allows the transmission code to be pro-
grammed remotely, without using the SEL button on the unit it-
self.
To programme a transmission code remotely, proceed as fol-
lows: send the radio control code continuously for more than 10
seconds; the control unit will enter the programming mode as
described above for the CODE LED in the main menu.
The control unit is supplied by the manufacturer with remote
programming of a transmission code not enabled; to enable the
function proceed as follows: check that the extended menu is
enabled (T. MOT. and WIND SPEED LEDs start flashing altern-
ately), use the SEL button to navigate to the CODE LED when
flashing and press the SET button: the CODE LED remains lit
in a constant manner and programming is complete. Repeat
the procedure to restore the previous configuration.
B) SENS. CODE (Safety upward movement):
The control unit is supplied by the manufacturer with the Safety
upward movement function disabled; if you wish to enable the
function, so that after 12 hours of Wind sensor inactivity the
control unit automatically sends a command for Safety upward
movement, proceed as follows: check that the extended menu
is enabled (T. MOT. and WIND SPEED LEDs start flashing al-
ternately), use the SEL button to navigate to the SENS. CODE
LED when flashing and press the SET button: the SENS.
CODE LED remains lit in a constant manner and programming
is complete. Repeat the procedure to restore the previous con-
figuration.
EXTENDED MENU 2
The control unit is supplied by the manufacturer with the only
option of selecting the functions listed in the main menu dir-
ectly.
To enable the functions in extended menu 2, proceed as fol-
lows: access extended menu 1 (as described in the corres-
ponding paragraph), then press the SET button again and hold
3
Rev. 1.1 03/12/10
