400MM HORIZONTAL BANDSAW WITH
HYDRAULIC ARM
MODEL NO:
SM353CE.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with
the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply off and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
9
Familiarise yourself with the application and limitations of the saw, as well as the specific potential hazards.
9
Ensure that all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to.
WARNING!
Take care lifting the bandsaw arm as it is heavy, and could, if not correctly lifted, affect the whole balance of the machine.
8
DO NOT
operate the bandsaw unless all blade guards are installed and in proper working order.
8
DO NOT
operate the bandsaw with the blade in the fully raised position.
8
DO NOT
leave the machine running unattended.
8
DO NOT
operate the machine if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT
use the bandsaw for a task it is not designed to perform.
8
DO NOT
use damaged or deformed bandsaw blades.
8
DO NOT
remove the safety guard whilst in use.
8
DO NOT
hold the workpiece by hand.
8
DO NOT
touch the workpiece immediately after cutting, it may be very hot.
8
DO NOT
operate the machine when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9
Ensure the machine is situated on a solid surface, adequate for supporting the weight of the machine and the workpiece.
9
Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
9
Disconnect bandsaw from the electric power supply before changing accessories, making repairs or adjustments.
9
Wear approved safety eye protection and ear defenders.
9
Maintain correct balance and footing, ensure the floor is not slippery and wear non-slip rubber soled footwear.
9
Always provide adequate support for long and heavy material.
8
DO NOT
turn bandsaw on until the workpiece is secured in the vice and the blade has been positioned just above the workpiece.
8
DO NOT
over tighten the blade as it will stretch and warp.
8
DO NOT
allow children or untrained persons to operate the machine. Keep them away from the work area.
9
Check the alignment of moving parts regularly; for safest performance keep the machine clean at all times.
9
Turn off the machine before raising the blade
9
Avoid unintentional starting.
Recommended fuse rating
13 Amp
S
M353CE.V3 Issue 1 23/01/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Electrical shock
hazard
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
Indoor use only
