5. maintenanCe
5.1.
CHanging tHe batteries
5.1.1.
This inflator requires 2 x AAA batteries. If the voltage of the batteries fall below 2.6 volts,
the battery icon will flash continuously until it shuts down. If the voltage of the batteries fall
below 2.5 volts, the low “LO” battery icon appears while the power is on and then shuts down
automatically. The batteries must be changed if the battery icon flashes.
5.1.2.
Unscrew the battery cap (fig.1).
5.1.3.
Slide the batteries into the inflater with the positive end facing out of the inflater (fig.1).
5.1.4.
Replace the battery cap carefully and
Do not
over tighten (fig.1).
5.2.
sCale CHange
5.2.1.
Press and hold the scale change button to
activate the display, once the display is
activated press and hold the button
for 2 seconds to change the display
scale (fig.2).
6. troublesHooting
This air line gauge has been engineered to give years of trouble-free service. Major faults are
often due either to prolonged mistreatment or to a dirty, excessively wet air supply. The following guide will enable the operator or
service engineer to diagnose and cure any problems which may arise.
6.1.
air leaks from tyre ConneCtor
The seals should be replaced when it becomes difficult to obtain an easy, positive airtight seal on a tyre valve. New chucks are
available from Sealey Stockists.
6.2.
DamageD flexible Hose (gauge to tyre ConneCtor)
The complete hose assembly should be replaced immediately if any sign of deep chafing, bulging or cracking appears. Ensure
that the centred filter in the gauge outlet port does not become dislodged during replacement.
6.3.
slow tyre inflation
Caused by: Low supply pressure, or blocked inlet filter, or damaged valve mechanism.
fig.1
fig.2
reference pressure psi
29.0
58.0
87.0
116.0
145
174
allowable tolerances
+/- 1.2 psi +/- 1.2 psi
+/- 2.3 psi +/- 2.3 psi +/- 3.6 psi +/- 3.6 psi
indicated pressure psi
Calibration CertifiCate
tyre inflater
Model no:
sa374, sa375
This tyre inflater has been calibrated in its normal working position on test equipment with an accuracy that is traceable to standards
according to: EN12645:2014. (Tyre pressure measuring instruments, devices for inspection of pressure and/or Inflation/deflation of tyres for
motor vehicles.)
Physical Laboratory Reference Number L0134, Reference Pressure Indicator Keyence AP-C33, Serial Number E031759.
serial no.
Date:
test results
sealey group, kempson way, suffolk business Park, bury st edmunds, suffolk. iP32 7ar
01284 757500
01284 703534
www.sealey.co.uk
environment ProteCtion
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
weee regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
battery removal see seCtion 5
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.
note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important
: No Liability is accepted for incorrect use of this product.
warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
SA374 SA375 Issue 1 10/06/19
Original Language Version
© Jack Sealey Limited
