IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions and maintained properly, give you years of trouble free performance.
Refer to Instruction
Manual
Wear safety
footwear
1. SAFETY
RJA2500.V2 Issue: 1 - 21/02/17
Original Language Version
© Jack Sealey Limited
INSTRUCTIONS FOR:
TROLLEY JACK 2.5TONNE ALUMINIUM
ROCKET LIFT
MODEL No
:
RJA2500.V2
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.
Use
genuine parts only. The use of non-genuine parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area.
Keep working area clean and tidy and free from unrelated materials.
Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in
.
Chock wheels of vehicle
.
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc. to allow for vehicle tilting.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
Ensure there are no passengers in the vehicle.
Place jack under only those lifting points recommended by vehicle manufacturer
(see vehicle handbook).
Check that the lifting point is stable and centred on the jack saddle.
Ensure the jack wheels are free to move and that there are no obstructions.
DANGER:
Use the jack for lifting only,
NOT
for supporting the lifted load.
Use suitable axle stands under the vehicle before proceeding with any task.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
Use a qualified person to lubricate and maintain the jack.
Ensure that only
hydraulic jack oil
is used in the jack.
DO NOT
operate the jack if damaged.
DO NOT
allow untrained persons to operate the jack.
DO NOT
operate the jack when tired or under the influence of drugs, alcohol or intoxicating medication.
DO NOT
exceed the rated capacity of the jack.
DO NOT
allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
DO NOT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
DO NOT
work under the vehicle until appropriately rated axle stands have been correctly positioned.
DO NOT
use the jack for purposes other than that for which it is intended.
DO NOT
top up hydraulic system with brake fluid. Use hydraulic jack oil only. (Sealey Part No: HJO500MLS or HJO5LS)
DO NOT
adjust the safety overload valve.
When not in use store the jack, fully lowered, in a safe, dry, childproof location.
2. INTRODUCTION
3. SPECIFICATION
Model No
: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJA2500.V2
Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5tonne (2500kg)
Minimum Saddle Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95mm
Maximum Saddle Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485mm
Maximum Chassis Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160mm
Length:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725mm
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26kg
4. ASSEMBLY
4.1. Assembly.
4.1.2. Remove the retaining wedge prior to assembling the jack handle. Press the handle socket downwards and pull out the wedge holding the
pump yoke down (fig.1). Retain the wedge for future transportation.
4.1.3. Insert the upper handle into the lower handle. The locking ball will lock the two pieces together.
4.1.4. Loosen the handle retaining screw from the handle socket.
4.1.5. Insert the pump handle into the handle socket, fully engaging the universal joint of the release valve.
4.1.6. Ensure that the handle is correctly inserted into the socket, then tighten the handle retaining screw.
4.2.
Purging Hydraulic System.
4.2.1. Open the release valve by turning the handle one full turn anti-clockwise.
4.2.2. Pump the handle a minimum of twenty full strokes.
4.2.3. Close the release valve by turning the handle clockwise.
Made primarily for the motor racing enthusiast, this jack weighs in at just 26kg. Utilises many weight-saving techniques such as a skeletal lift arm.
Features Rocket Lift by use of twin pistons, bringing saddle to maximum height in minimal pumps. Polyurethane wheels for smooth and quiet
manoeuvring, which also limits damage to garage floors. Lifting bars are fitted either side of the anodised aluminium chassis enabling fast,
lightweight pick-up.
