Sealey Quality MACHINERY SM46.V3, Инструкции

Страница: 2 / 3

the sM46.V3 is designed to extract dust, saw dust and other fine debris from wood machining. It should not be used to extract metallic
debris, glass or water.
2. APPLICATION & SPECIFICATION
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600cfm
Impeller diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225mm
Intake diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mm
flexible hose diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mm
flexible hose maximum length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5m
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V, 50Hz, 746W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28kg
noise level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<87dBA
Specification:
Description:
• Collector body with motor • Filter/Collector Bag x 2 • Collector
• Seal • Column • Support Rod x 3
• Base plate • Screws, nuts, washers (1 bag) • Castors x 4
• Inlet Hose (2m)
3. CONTENTS & ASSEMBLY
Note: Numbers in brackets are the item numbers on the parts diagram and in the parts list.
3.1 Attach the four castors (1) to the underside of the base (4) using screws (2), washers (3 &29) and nuts (30). support base (4) on
battens, or similar, raising castors clear of floor to give stability for the following assembly tasks.
3.2 With screws (14) and washers (12) attach column (20) to base plate (4).
3.3 Attach motor (18) to column (20), so that collector body is positioned as shown in parts diagram,
with screws (14) and washers (12).
3.4 Install collector (23) to collector body (11) using packing (22) and flange head screws (15).
Ensure collector is directly over base.
3.5 Attach collector support rods (31) to base with screws (15), washers (32) and nuts (33) and to
collector with screws (2), washers (29) and nuts (30).
3.6 Attach filter bag support (35) to collector with screws (34).
3.7 fit upper (filter) bag (25) over upper bag flange on collector (23) and secure by tightening built-in
strap. Hook loop on end of bag (25) over support arm (35). fit second (collector) bag (24) to lower
bag flange on collector.
note: Bag clamps (34) are provided and may be used for additional bag security.
3.9 Adjust screw (fig.1.A) to bear lightly against the side of the collector body (B) and lock by tightening
nut (c).
unpack the extractor components and check that all are present and undamaged. In case of shortage or damage please contact the supplier.
4. OPERATING INSTRUCTIONS
5. DECLARATION OF CONFORMITY

WARNING! before operating the extractor ensure that you read, understand and apply the safety instructions in Section 1.
4.1 confirm that supply voltage matches the voltage shown on the motor data plate and that the motor switch (16) is ‘off’.
4.2 connect extractor hose to the inlet (6) on the collector body (11) and attach other end to extractor point on equipment.

WARNING! DO NOT operate extractor without the hose attached.
4.3
Plug into mains supply and press motor switch ‘on’.
4.4 Ensure that the lower bag is emptied of dust and chips on a regular basis and is not allowed to become full.
Note: fitting a reducer to the extraction hose will reduce the volume of dust extracted.

WARNING! this unit is not suitable to be used to extract dust via a piped system.
Declaration of Conformity
We, the sole importer into the uK, declare that the product listed here is in conformity with the following standards and
directives.
the construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
DUST & CHIP EXTRACTOR
Model SM46.V3
2006/95/Ec Low Voltage Directive
2004/108/Ec EMc Directive
2006/42/Ec Machinery Directive
93/68/EEc cE Marking Directive
signed by Mark sweetman 16th March 2009
fig. 1
01284 757500
01284 703534
sales@sealey.co.uk
Sole UK Distributor
Sealey Group,
Bury st. Edmunds, suffolk.
www.sealey.co.uk
Web
email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
sM46.V3 Issue no: 3 - 16/03/09