Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
3
Follow all workshop Health & Safety rules, regulations and conditions when using this tool.
p
WARNING!
Disconnect from air supply before servicing.
3
Maintain tool in good condition and replace any damaged or worn parts.
Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
p
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use
and ensure that all connections are secure.
p
WARNING!
Always wear approved eye and face protection when operating the tool.
3
Wear ear defenders and gloves if necessary.
3
Keep hands and body clear of the workpiece when operating the tool.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure unstable workpiece with a clamp, vice or other adequate holding device.
3
Keep children and non-essential persons away from the work area.
7
DO NOT
get the tool wet or use in damp or wet locations.
7
DO NOT
hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
7
DO NOT
use the tool for a task it is not designed to perform.
p
p
WARNING! DO NOT
use the tool if damaged or faulty. Contact your local service agent.
7
DO NOT
use the tool unless you have been instructed in its use by a qualified person.
7
DO NOT
carry the tool by the air hose, or yank the hose from the air supply.
7
DO NOT
direct air from the air hose at yourself or others.
7
DO NOT
operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.
3
When not in use, disconnect from air supply and store in a safe, dry, childproof location.
SA36.V2 - 1 -290802
Model:
SA36.V2
01284 757500
E-mail:
Web:
www.sealey.co.uk
01284 703534
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date. proof of which will be required for any claim.
INFORMATION:
Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
Sole UK Distributor, Sealey Group
, Bury St. Edmunds, Suffolk.
Issue:
1
Date Issue:
290802
Item Part No.
Description
1
SA36.V2-01
Clamp
2
SA36.V2-02
Set Screw
3
SA36.V2-03
Punch Die
4
SA36.V2-04
Guide Bushing
5
SA36.V2-05
Cup Spring
6
SA36.V2-06
Punch
7
SA36.V2-07
Screw
8
SA36.V2-08
Cover Plate
9
SA36.V2-09
Anvil
10
SA36.V2-10
Oil Seal
11
SA36.V2-11
Support Ring
12
SA36.V2-12
O-ring
13
SA36.V2-13
Oil Plug
14
SA36.V2-14
O-ring
15
SA36.V2-15
Hydraulic Cylinder
16
SA36.V2-16
Air Cylinder
17
SA36.V2-17
Plastic Wrap
18
SA36.V2-18
Valve Body
Item Part No.
Description
19
SA36.V2-19
Air Inlet
20
SA36.V2-20
Throttle Lever
21
SA36.V2-21
Spring Pin
22
SA36.V2-22
O-ring
23
SA36.V2-23
Push Rod
24
SA36.V2-24
Spring
25
SA36.V2-25
Valve
26
SA36.V2-26
Spring
27
SA36.V2-27
O-ring
28
SA36.V2-28
Screw
29
SA36.V2-29
O-ring
30
SA36.V2-30
Support Ring
31
SA36.V2-31
Hydraulic Piston
32
SA36.V2-32
O-ring
33
SA36.V2-33
Support Ring
34
SA36.V2-34
Spring
35
SA36.V2-35
Piston
36
SA36.V2-36
O-ring
INSTRUCTIONS FOR
AIR PUNCH/FLANGE TOOL
2.
INTRODUCTION & SPECIFICATION
Noise . . . . . . . . . . . . . . . . . .81.7dB(A)
Spare Punch . . . . . . . . . . . . .SA36/36
Spare Die . . . . . . . . . . . . . . . SA36/40
Operating Pressure . . . .90psi (6.2 bar)
Air Inlet . . . . . . . . . . . . . . . . . 1/4BSP
Weight . . . . . . . . . . . . . . . . . . . . 1.3kg
Vibration . . . . . . . . . . . . . . . . .<2.5m/s
2
2.1. Introduction
Suitable for heavy bodyshop use. Aluminium alloy body with steel punch and die. Puts a 10mm flange
onto car-panel-thickness sheet for lap jointing and puts 6mm holes in panels for mig spot-welding.
2.2. Specification
