Sealey MIGHTYMIG 150 Скачать руководство пользователя страница 8

Страница: 8 / 9

EC DECLARATION

OF CONFORMITY

We the sole importers into the UK, hereby declare that the equipment described below

Description and Function:...............................................................................................................................................

Model/Type:.....................................................................................................................................................................

Manufacturing Date / Serial number (optional).................................................................................................................

Manufacturer's authorised representative within the EC:

Jack Sealey Ltd. Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk, IP32 7AR

Conforms to the requirements of the following Directives, as indicated.

2006/42/EC Machinery Directive

2000/14/EC Outdoor Noise Emissions Directive

2006/95/EC Low Voltage Directive 2002/96/EC WEEE Directive

2004/108/EC EMC Directive

2002/95/EC RoHS Directive

93/68/EEC CE Marking Directive 97/23/EC Pressure Equipment Directive

And the following harmonised standard(s):…………………………………………………..................................................

……………………………………………………………………………………………….......................................................

Additional technical standards and specifications (if applicable):………………………………............................................

……………………………………………………………………………………………….......................................................

Technical file compiled by:

Jack Sealey Ltd

Signed:

……………………………………..

Date:

……………………………….............

Place:

Bury St.Edmunds.

Name:

…………………………………………

Position:

…………………………………....

Being the responsible person appointed by the manufacturer.

Gas/No-Gas MIG Welder 150Amp 230V

MIGHTYMIG150

BS EN 60974 part 1: 2005 BS EN 60974 part 10: 2007

09-Aug-2010

Mark Sweetman

Managing Director

Содержание MIGHTYMIG 150










Результаты поиска

Содержание MIGHTYMIG 150

Отзывы:

Похожие инструкции для MIGHTYMIG 150

Бренды по названию

Популярные бренды

Sealey MIGHTYMIG 150, Руководство пользователя

Результаты поиска

Содержание MIGHTYMIG 150

Отзывы:

Похожие инструкции для MIGHTYMIG 150

Бренды по названию

Популярные бренды