CPG8V Issue 3 13/09/21
Original Language Version
© Jack Sealey Limited
2. INTRODUCTION
Lightweight versatile cordless grease gun, producing 3000psi. Ideal for on site jobs where space is at a premium. Suitable for 85g/3oz and
400g/14oz cartridges. Supplied with 330mm
fl
exi and 175mm rigid delivery nozzles, 85g and 400g cartridge, a 400g cartridge adaptor and 2Ah
8V battery and mains charger.
3. SPECIFICATION
Model:
.......................................................................
CPG8V
Battery: ................................................... 8V 2Ah Lithium-ion
Hose length: ..................... Rigid = 175mm. Flexible = 330mm
Pressure: ...................................................................3000psi
Replacement parts: .....................CPG8VBP - 8V 2Ah battery
4. OPERATION
IMPORTANT WARRANTY INFORMATION:
the battery pack fitted to this cordless tool are considered to be a consumable item and its ability
to accept charge will reduce over time. We will provide warranty against mechanical and electrical defect for a period of one year - this does not
cover fair wear and tear. If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these
circumstances we will not replace the battery pack even if it is less than one year old.
4.1.
CHARGING THE BATTERY
IMPORTANT:
Before using the grease gun for the first time the battery must be fully charged
4.1.1.
To charge the battery place the battery into the charging base.
NOTE:
The battery can only be inserted into the charger one way. If the battery will not fit into the charger, rotate it by 180º.
4.1.2.
Plug the charger into the mains. The green LED, on the left hand side, will turn on. When the battery is being charged the red LED,
on the right hand side will turn on and the green LED will turn off. When the battery is fully charged, the red LED will turn off and the
green LED will turn on.
NOTE:
A completely discharged battery will take approximately 2 hours to become fully charged.
4.2.
I
NSTALLING THE BATTERY
4.2.1.
Remove the discharged battery from the grease gun handle by pressing the battery release buttons on the sides of the battery.
4.2.2.
Insert a fully charged battery into the battery cavity in the grease gun handle. The battery release buttons will “click” when the battery is
fully
inserted.
NOTE:
The battery can only be inserted into the handle one way. If the battery will not fit into the handle, rotate it by 180º.
4.3.
ATTACHING THE DELIVERY NOZZLE
4.3.1.
Thread the rigid or flexible delivery nozzle into the front of the grease gun and tighten using a 15mm wrench. Do not over tighten.
4.4.
LOADING A GREASE CARTRIDGE (3oz/85g) INTO THE SMALL CARTRIDGE HOLDER
4.4.1.
Pull the follower rod (fig 1 - 1) out and towards the side of the cartridge (fig 1 - 2) as far as possible until the groove on the follower rod
engages with the slot in the end cap.
4.4.2.
Remove the plastic cap from the bottom of the grease cartridge (fig 1 - 3).
4.4.3.
Insert the bottom of the grease cartridge into the cartridge holder and push the cartridge fully in.
NOTE:
The top of the grease cartridge should not extend beyond the end of the cartridge holder.
4.4.4.
Remove and peel away tab on top side of grease cartridge.
WARNING!
Be careful not to bump the follower rod as it is spring loaded. This will result in the rapid ejection of grease and the
cartridge.
4.5.
ATTACHING THE SMALL CARTRIDGE (3oz/85g)
NOTE:
Remove the large tube threaded adaptor (fig 2 - 4) from the grease gun, if applicable. Turn the cartridge adaptor
clockwise (left hand thread).
4.5.1.
Thread the loaded small cartridge into the grease gun by turning it counter-clockwise (left hand thread). Hand tight only.
4.5.2.
Release the following rod (fig 1 -1) by moving it sideways towards the centre of the grease tube. When released, slowly push the
follower rod back into the cartridge.
4.6.
LOADING A GREASE CARTRIDGE (14oz/400g) INTO THE LARGE CARTRIDGE HOLDER
NOTE:
Loading a grease cartridge (fig 2 - 3) into the large cartridge holder (fig 2 - 2) is similar in operation to loading the smaller
cartridge.
4.6.1.
Pull the follower rod out (fig 2 - 1) as far as possible.
NOTE:
The follower rod has a self-locking latch and will lock automatically.
4.6.2.
Repeat steps 4.4.2, 4.4.3 and 4.4.4 as listed above.
fi
g.1
