Seagull SEA53B Скачать руководство пользователя страница 2

Страница: 2 / 20

YAK 54.

Instruction Manual.

INTRODUCTION.

Thank you for choosing the

YAK 54

ARTF

by SG MODELS . The

YAK 54

was designed with

the intermediate/advanced sport flyer in mind. It is a semi scale airplane which is easy to fly and

quick to assemble. The airframe is conventionally built using balsa, plywood to make it stronger than

the average ARTF, yet the design allows the aeroplane to be kept light. You will find that most of the

work has been done for you already.Flying the

YAK 54

is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your

YAK 54

. Use the parts listing below to identify

all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C

supplier and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

procedures designed to help the new pilot on his way to successful R/C flight. They will also be able

to advise on any insurance and safety regulations that may apply.

ADDITIONAL ITEMS REQUIRED.

.91-1.25 2-4 stroke engine.

20cc gasoline engine.

Computer radio with six digital

servos.

Glow plug to suit engine.

Propeller to suit engine.

Protective foam rubber for radio

system.

Silicone fuel line.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modelling knife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

(1) Canopy hatch.

WING ASSEMBLY

(1) Right wing half/ aileron.

(1) Left wing half/ aileron.

(1) Aluminium dihedral brace.

Tail section assembly

(1) Horizontal stabilizer/ elevator

halves.

(1) Rudder halves.

Some more parts.

HARDWARE PACK

COWLING

Landing gear.....

Содержание SEA53B





















Результаты поиска

Содержание SEA53B

Отзывы:

Бренды по названию

Популярные бренды

Seagull SEA53B, Инструкция по сборке

Результаты поиска

Содержание SEA53B

Отзывы:

Бренды по названию

Популярные бренды