Seagull cassutt 3M Racer Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 23

Seagull cassutt 3M Racer Скачать руководство пользователя страница 2

CASSUTT 3M RACER.

Instruction Manual

2

INTRODUCTION.

Thank you for choosing the

CASSSUTT 3M RACER

ARTF by SEAGULL MODELS COMPANY

LTD. The

CASSSUTT 3M RACER

was designed with the intermediate/advanced sport scale in

mind. It is a semi scale airplane which is easy to fly and quick to assemble. The airframe is
conventionally built using balsa, plywood to make it stronger than the average ARTF , yet the design
allows the aeroplane to be kept light. You will find that most of the work has been done for you already.
The motor mount has been fitted and the hinges are pre-installed . Flying the

CASSSUTT 3M

RACER

is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your

CASSSUTT 3M RACER

. Use the parts listing

below to identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it
is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C
supplier and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.

KIT CONTENTS

1

3

3

2

2

6

4

5

7

8

9

10

11

«
1
2
3
4
...
»

Содержание cassutt 3M Racer
























Отзывы:

Нет отзывов