Seagull Models RACER DELTA 40-46 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 27

background image

RACER DELTA 40-46

Instruction Manual.

6

Use a pin vise and a small drill bit to drill

small pilot holes in the servo mount for the

servo mounting screws. Use the screws sup-

plied with your radio system to mount the

servo in place on the servo mount. Repeat

this procedure to mount the servo in the op-

posite panel.

Epoxy.

Aileron control horn.

INSTALLING THE AILERON SERVOS.

AILERON PUSHROD INSTALLATION.

Please see below pictures.

12.5mm

M3 clevis.

M3 lock nut.

14.5mm

«
...
4
5
6
7
8
...
»

Содержание RACER DELTA 40-46




























Отзывы:

Нет отзывов

Похожие инструкции для RACER DELTA 40-46

Бренд: GAME OF BRICKS Страницы: 30

Strike Eagle G1670B Cargo Plane

Бренд: Laser Pegs Страницы: 8

Бренд: Laser Pegs Страницы: 2

Бренд: WattAge Страницы: 32

BABY born 823583

Бренд: Zapf Creation Страницы: 54

Бренд: E-FLITE Страницы: 32

Бренд: MegaTech Страницы: 12

Little Tikes Fantastic Firsts Spinning RC

Бренд: MGA Entertainment Страницы: 2

P-51 MUSTANG EP RTF

Бренд: WattAge Страницы: 24

Бренд: Miniature Aircraft USA Страницы: 33

Бренд: LEGO Страницы: 76

Baby Beats Monkey Drum

Бренд: VTech Baby Страницы: 11

Бренд: marklin Страницы: 24

SPACECHAOS DARK PIRATES 5104

Бренд: Meccano Страницы: 24

Mikey's Swing-Arm Bike 12009

Бренд: K'Nex Страницы: 23

Бренд: Faller Страницы: 16

IAF TC-2 Trainer Kfir

Бренд: Wingman Models Страницы: 7

Бренд: Faller Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды