manualshive.com logo in svg

Seagull Models MINI CHRISTEN EAGLE II N54CE, Инструкция по сборке

Поделиться
Скачать
Seagull Models MINI CHRISTEN EAGLE II N54CE Скачать руководство пользователя страница 3

3

www.seagullmodels.com

KIT CONTENTS.

ADDITIONAL ITEMS REQUIRED.

Motor  480
4 channel radio with 4 mini servos
Speed control (ESC) 30A-40A amp.
Battery 2-3-cell 2200mAh to
2600mAh Li-Po.

The control surfaces, including the
ailerons, elevators, and rudder, are
prehinged with hinges installed, but
the hinges are not glued in place. It
is imperative that you properly
adhere the hinges in place per the
steps that follow using a high-quality
thin C/A glue.

HINGING THE AILERONS .

Note:

 

1) Carefully remove the aileron from one

of the wing panels. Note the position of the
hinges.

 

2) Remove each hinge from the wing panel

and aileron and place a T-pin in the center of
each hinge. Slide each hinge into the aileron
until the T-pin is snug against the aileron. This
will help ensure an equal amount of hinge is
on either side of the hinge line when the aileron
is mounted to the wing panel.

Hinge.

T-pin.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue
30 minute epoxy
5 minute epoxy
Hand or electric drill
Assorted drill bits
Modelling knife
Straight edge ruler
2mm ball driver
Phillips head screwdriver
220 grit sandpaper
90° square or builder’s triangle
Wire cutters
Masking tape & T-pins
Thread-lock
Paper towels

 

3) Slide the aileron on the wing panel until

there is only a slight gap. The hinge is now
centered on the wing panel and aileron.
Remove the T-pins and snug the aileron
against the wing panel. A gap of 1/64” or less
should be maintained between the wing panel
and aileron.

SEAX10401

Fuselage

SEAX10402

 Wing Set

SEAX10403

Tail Set

SEAX10404

Cowling

SEAX10405

Landing Gear Set

SEAX10406

Canopy Hatch

SEAX10407

Wing Tube

SEAX10408

Hardware

SEAX10409

Pushrod Set

Содержание MINI CHRISTEN EAGLE II N54CE























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды