Seagull Models MINI CHRISTEN EAGLE II N54CE Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 22

background image

MINI CHRISTEN EAGLE II N54CE

Instruction Manual.

18

ATTACHMENT WING-FUSELAGE.

Wing tube.

Attach the carbon fiber into fuselage.

Insert two wing panels as pictures below.

Wing bolt.

INSTALLING THE RECEIVER.

Receiver.

1) Plug the five servo leads and the switch

lead into the receiver. Plug the battery pack
lead into the switch also.

2) Wrap the receiver pack in the protec-

tive foam rubber to protect them from vibra-
tion.

3) Route the antenna in the antenna tube

inside the fuselage and secure it to the bot-
tom of fuselage using a plastic tape.

M3x6mm.

«
...
16
17
18
19
20
...
»

Содержание MINI CHRISTEN EAGLE II N54CE























Отзывы:

Нет отзывов

Похожие инструкции для MINI CHRISTEN EAGLE II N54CE

Бренд: Hobbico Страницы: 28

Premier SD50 Diesel Engine

Бренд: MTHTrains Страницы: 47

Бренд: Gym Dandy Страницы: 14

Бренд: WARCRADLE SCENICS Страницы: 35

WOODEN PROJECT WORKBENCH

Бренд: Melissa & Doug Страницы: 16

Count 'n Go Snail

Бренд: VTech Страницы: 5

Бренд: PARKZONE Страницы: 24

Бренд: roco Страницы: 56

Zoom F/A-18C Hornet S.A.

Бренд: Eduard Страницы: 3

Ultra Micro DH 98 Mosquito Mk VI

Бренд: PARKZONE Страницы: 64

Mini HIGHroller

Бренд: Team Losi Страницы: 20

Grumman F7 F-3 Tigercat

Бренд: Aeronaut Страницы: 9

Бренд: Nincocean Страницы: 12

L-19/0-1 BIRD DOG 1730mm Wingspan

Бренд: Radio control model Страницы: 32

Бренд: Skymaster Страницы: 14

Future Gothic B08-FG Series

Бренд: BLOTZ Страницы: 3

Бренд: starwaders Страницы: 24

Бренд: Eduard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды