manualshive.com logo in svg

Seagull Models MINI CHRISTEN EAGLE II N54CE, Инструкция по сборке

Поделиться
Скачать
Seagull Models MINI CHRISTEN EAGLE II N54CE Скачать руководство пользователя страница 19

19

www.seagullmodels.com

INSTALLATION WING STRUTS.

    1)Locate the items for this section of the
manual.

    2)Attach the wing strut to the top of the
bottom wing panel using an M3x6 machine
screw.

    3)Repeat steps  to prepare the remaining
wing panel for installation.

Place the Fuselage Hatch back on the fuselage
to complete the assembly of your models.

M3x6mm.

M3x6mm.

    3)Thread a clevis on each end of a threadded
rod.Connect the rod between the top and
bottom ailerons.With the radio sysytem on and
the bottom aileron contered ,adjust the length
to center the top aileron.Once centered ,slide
the silicone tubing over the forks of the clevis
to prevent it from opening accidentally.Apply
threadlock on the nuts and clevises to prevent
them from vibrating loose.Use needle nose
pliers to tighten the nut against the clevis to
prevent it from vibrating and changing position.

M3x6mm.

150mm.

150mm.

Содержание MINI CHRISTEN EAGLE II N54CE























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды