Seagull Models MINI CHRISTEN EAGLE II N54CE Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 22

background image

1

www.seagullmodels.com

ASSEMBLY MANUAL

MS: X104

Specifications:

Wing span ----------------- 35.4in (90.0cm).
Wing area ------------------392.2sq.in (25.3sq dm).
Weight -----------------------3.5lbs (1.6kg).
Length -----------------------31.0in (78.8cm).
Speed control(ESC)-----30A-40A amp.
Motor ------------------------ 480.
Radio ----------- 4 channels with 4 mini servos.
Battery 2-3-cell 2200mAh to 2600mAh Li-Po.
10 x 5E Electric Prop.

“Graphics and specifications may change without notice”.

1
2
3
...
»

Содержание MINI CHRISTEN EAGLE II N54CE























Отзывы:

Нет отзывов

Похожие инструкции для MINI CHRISTEN EAGLE II N54CE

SM-79 Sparviero Exterior

Бренд: Eduard Страницы: 4

minideices 17865

Бренд: Lansay Страницы: 2

Бренд: BUSCH Страницы: 8

Бренд: Multiplex Страницы: 17

Бренд: Connoisseur Models Страницы: 14

Бренд: Volvo Страницы: 10

WILD THING 74180

Бренд: Fisher-Price Страницы: 28

Seahorse Symphony 643415

Бренд: Little Tikes Страницы: 2

Бренд: Multiplex Страницы: 36

Бренд: Madcow Rocketry Страницы: 3

TIME-TO-LEARN PRESCHOOL K2866

Бренд: Fisher-Price Страницы: 6

Wasp Indoor/Outdoor Helicopter 8632

Бренд: Excalibur Страницы: 1

Бренд: Gyros Страницы: 14

Harrier GR Mk.7/9 upgrade set

Бренд: Eduard Страницы: 3

My First THOMAS AND FRIENDS RAILWAY PALS

Бренд: Fisher-Price Страницы: 4

Бренд: Fisher-Price Страницы: 4

CONVERGENCE VTOL

Бренд: Horizon Hobby Страницы: 20

Бренд: Fisher-Price Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды