Seagull Models Extra 260 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 23

background image

www.seagullmodels.com

13

Repeat the procedure for orther
elevator.

!

1) Position the rudder control horn on the

left - right side of the rudder.

!

2) Locate the two nylon control horns, two

nylon control horn backplates and three
machine screws.

3x30mm.

2x30mm.

RUDDER CONTROL HORN

INSTALLATION.

Rudder
control horn.

!

5)

Mount the control horns by inserting the

bolts through the control horn bases and
elevator halves, then into the mounting
backplates. Do not overtighten the nuts or the
backplates may crush the wood.

!

3) Position the rudder horn on the both

side of rudder. The clevis attach- ment holes
should be positioned over the hinge line.

!

4) Using a 1.5mm drill bit and the control

horns as a guide, drill the mounting holes
through the rudder halves.

Rudder

control horn.

AILERON PUSHROD INSTALLATION.

Pushrod.

55mm.

C/A glue.

M3 lock nut.

Aileron pushrods assembly follow pictures

below.

«
...
11
12
13
14
15
...
»

Содержание Extra 260
























Отзывы:

Нет отзывов

Похожие инструкции для Extra 260

Бренд: Laser Pegs Страницы: 2

Pop & Roll Ball Tower

Бренд: VTech Страницы: 13

Бренд: Ultrafly Страницы: 16

Golden Age Series

Бренд: Rage Страницы: 10

Бренд: Faller Страницы: 4

Jungle Gym: Step & Count Kangaroo

Бренд: VTech Страницы: 11

VOICE TECH RESCUE HEROES Wendy Waters Firefighter

Бренд: Fisher-Price Страницы: 2

Бренд: Trix Страницы: 20

Cash Bash Electronic Flash Card LER 6966

Бренд: Learning Resources Страницы: 4

N-Strike Mega Bulldog

Бренд: Nerf Страницы: 2

Impulse Laser Gun Rifle Set

Бренд: Jamara Страницы: 8

Бренд: Rapido Trains Страницы: 21

Baby Wow Walking Megan

Бренд: IMC Toys Страницы: 2

NUM NOMS 547334

Бренд: MGA Entertainment Страницы: 2

Бренд: Extreme RC Страницы: 4

Бренд: Quadro mdb Страницы: 8

Бренд: marklin Страницы: 12

Бренд: Kangke Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды