Seagull Models Extra 260 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 23

background image

EXTRA 260.

Instruction Manual.

12

INSTALLING THE AILERON LINKAGE.

!

1) Aileron control horn:

Mix a small amount of 30 minute epoxy and
lightly coat the inside of the hole in the aileron
and the control horn screw.

!

2) Thread the screw (insert the aluminium

washer) into the hole from the top of surface.
Wipe away any excess epoxy on the wing and
screw with rubbing alcohol and a paper towel.
Screw the M3 nut (insert the aluminium
washer) in place as shown. Alllow the epoxy
to fully cure.

Wing.

Aileron.

Aluminium washer.

M3 nut.

M3 lock nut.

Wing bottom.

M3 control horn.

Wing bottom.

Aileron control horn.

Repeat the procedure for orther wing.

3x45mm.

C/A glue.

ELEVATOR CONTROL HORN INSTALLATION.

!

1) Elevator control horn:

Mix a small amount of 30 minute epoxy and
lightly coat the inside of the hole in the elevator
and the control horn screw.

!

2) Thread the screw (insert the aluminium

washer) into the hole from the top of surface.
Wipe away any excess epoxy on the fin and
screw with rubbing alcohol and a paper towel.
Screw the M3 nut (insert the aluminium
washer) in place as shown. Alllow the epoxy
to fully cure.

Horizontal fin.

Elevator

.

Elevator control horn.

«
...
10
11
12
13
14
...
»

Содержание Extra 260
























Отзывы:

Нет отзывов

Похожие инструкции для Extra 260

Бренд: Lancair Страницы: 8

Бренд: M.T.H. Страницы: 2

Бренд: Radio Flyer Страницы: 2

American Superliner 3820

Бренд: Italeri Страницы: 9

Бренд: ubisoft Страницы: 21

Бренд: Air Hogs Страницы: 6

Spitfire placards

Бренд: Eduard Страницы: 3

Бренд: E-FLITE Страницы: 19

Бренд: Fisher-Price Страницы: 2

Lokpuffer Puff-H0

Бренд: Fichtelbahn Страницы: 2

Laugh & Learn Smart Learning Home

Бренд: Fisher-Price Страницы: 20

Бренд: LEGO Страницы: 60

Бренд: Faller Страницы: 16

Бренд: PARKZONE Страницы: 12

Бренд: GREAT PLANES Страницы: 20

Бренд: POLA G Страницы: 4

Бренд: Faller Страницы: 8

Бренд: Masterpiece Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды