background image

10

Cheetah 15K.5 SCSI Product Manual, Rev. D

3.5.1

Programmable drive capacity

Using the Mode Select command, the drive can change its capacity to something less than maximum. See the 
Mode Select Parameter List table in the SCSI Interface Manual. Refer to the Parameter list block descriptor 
number of blocks field. A value of zero in the number of blocks field indicates that the drive shall not change the 
capacity it is currently formatted to have. A number in the number of blocks field that is less than the maximum 
number of LBAs changes the total drive capacity to the value in the block descriptor number of blocks field. A 
value greater than the maximum number of LBAs is rounded down to the maximum capacity.

3.6

Factory installed accessories

OEM Standard drives are shipped with the Cheetah 15K.5 Installation Guide, part number 100384777, and the 
Safety and Regulatory Agency Specifications, part number 75789512 (unless otherwise specified). The factory 
also ships with the drive a small bag of jumper plugs used for the J5 and J6 option select jumper headers (on 
LW models only).

3.7

Options (factory installed)

All customer requested options are incorporated during production or packaged at the manufacturing facility 
before shipping. Some of the options available are (not an exhaustive list of possible options):

• Other capacities can be ordered depending on sparing scheme and sector size requested.

• Single unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection 

against transit damage. Units shipped individually require additional protection as provided by the single unit 
shipping pack. Users planning single unit distribution should specify this option.

• The  Cheetah 15K.5 Installation Guide, part number 100384777, usually ships with each standard OEM 

drive. Extra copies may be ordered.

• The Safety and Regulatory Agency Specifications, part number 75789512, usually ships with each standard 

OEM drive. Extra copies may be ordered.

3.8

Accessories

The following accessories are available. All accessories may be installed in the field.
• Single unit shipping pack.

Содержание 15K.5 - Cheetah - Hard Drive































































































Отзывы: