Sea Tel ST88-21 C/Ku-Band TVRO, Инструкция по установке и эксплуатации

Страница: 95 / 145

ST88-21 C/Ku-Band TVRO Maintenance and Troubleshooting
13-11
1. If 465.0MHz Transmit Beacon is present, the fault is the BDE
modem.
2. If 465.0MHz Transmit Beacon is NOT present fault is with the
ADE modem.
13.6.3.1.7.
BDE Transmit or ADE Receive (PED M&C):
•
BDE Modem Tx Port Failure (Not transmitting at 452.5MHz) or
•
ADE Modem Rx Port Failure (Not receiving at 452.50MHz)
o
Install Spectrum Analyzer in line with the Rx IF coax path.
1. If 452.5MHz Transmit Beacon is present, the fault is the BDE
modem.
2. If 452.5MHz Transmit Beacon is NOT present, the fault is with
the ADE modem.
13.6.3.1.8.
BDE Receive or ADE Transmit (RF M&C):
•
BDE Modem Rx Port Failure (Not receiving at 460.0MHz) or
•
ADE Modem Tx Port Failure (Not transmitting at 460.0MHz)
o
Install Spectrum Analyzer in line with the Rx IF coax path.
1. If 465.0MHz Transmit Beacon in present, the fault is the BDE
modem.
2. If 465.0MHz Transmit Beacon is NOT present, the fault is with
the ADE modem.
13.6.3.1.9.
BDE Transmit Or ADE Receive (Radio M&C):
•
BDE Modem Tx Port Failure (Not transmitting at 447.5MHz) or
•
ADE Modem Rx Port Failure (Not receiving at 447.5MHz)
o
Install Spectrum Analyzer in line with the Rx IF coax path.
1. If 465.0MHz Transmit Beacon in present, the fault is the BDE
modem.
2. If 465.0MHz Transmit Beacon is NOT present, the fault is with
the ADE modem.
13.7. Troubleshooting
13.7.1. Theory Of Stabilization Operation
The antenna system is mounted on a three axis stabilization assembly that provides free motion with 3
degrees of freedom. This assembly allows the inertia of the antenna system to hold the antenna pointed
motionless in inertial space while the ship rolls, pitches and yaws beneath the assembly. Three low friction
torque motors attached to each of the three free axes of the assembly provide the required force to
overcome the disturbing torque imposed on the antenna system by cable restraints, bearing friction and small
air currents within the radome. These motors are also used to re-position the antenna in azimuth and
elevation.
The Pedestal Control Unit (PCU) uses inputs from the level cage sensors to calculate the amount of torque
required in each axis to keep the antenna pointed /-0.2 degrees. The primary sensor input for each
loop is the rate sensor mounted in the Level Cage Assembly. This sensor reports all motion of the antenna to
the PCU. The PCU immediately responds by applying a torque in the opposite direction to the disturbance to
bring the antenna back to its desired position. Both the instantaneous output of the rate sensor (Velocity
Error) and the integrated output of the rate sensor (Position Error) are used to achieve the high pointing
accuracy specification.
The calculated torque commands are converted to a 5 volt differential analog signal by a Digital to Analog
converter (D/A) and sent to each of three Brush-Less Servo Amplifiers. These amplifiers provide the proper
drive polarities and commutation required to operate the Brush-Less DC Servo Motors in torque mode. The
Torque acting on the mass of the antenna cause it to move, restoring the rate sensors to their original
position, and closing the control loop.
Since the rate sensors only monitor motion and not absolute position, a second input is required in each axis
as a long term reference to keep the antenna from slowly drifting in position. The Level and Cross Level