Sea Tel DAC-03 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 80

background image

DAC-03 Tracking Antenna Controller

Installation

4-1

4.

Installation

Below are basic steps to guide you in installing this equipment, but you may choose to complete installation steps in
a different order. Read this complete section before starting.
The following instructions describe the installation procedures for installing the DAC-03 Antenna Control Unit.
The installation of the Antenna Pedestal (ADE) is outlined in its Installation and Operation manual and may already
have been performed.

4.1.

General Cautions & Warnings

CAUTION - Electrical Shock Potentials exist on the Gyro Compass output
lines.

Assure that the Gyro Compass output is turned

OFF

when handling and

connecting wiring to the Terminal Mounting Strip.

CAUTION -

Allow only an

authorized dealer

to install or service the your Sea

Tel System components. Unauthorized installation or service can be dangerous
and may invalidate the warranty.

4.2.

Site Survey

Find the best location for the ACU and other Below Decks Equipment. Assure that each piece of equipment
is properly mounted. They should have sufficient cable to pull the equipment out of its mounting location
and disconnect the cables attached to it. There should be plenty of air space between units to allow heat to
vent off of the equipment. If the mounting location is a closed space, assure that the equipment will not be
damaged by trapped heat, install vents and/or fans to evacuate the heat. Refer to the Specifications of the
equipment installed for acceptable operating temperature.

4.3.

Preparing For The Installation

Always prepare for the installation before you actually start.

4.3.1.

Unpack Shipping Crates and Inspect / Inventory

Unpack the crates. Inspect everything to assure that all materials have been received and are in
good condition.

4.3.2.

Preparing BDE Location

Prepare the Rack (or other location) for the ACU, Terminal Mounting Strip and base multiplexer
panel. Prepare the mounting locations for the other Below Decks Equipment throughout ship.

4.3.3.

Read the Installation Information

Read the Installation section of the ACU and Antenna Pedestal manuals to be familiar with the
installation before attempting.

4.3.4.

Plan The Install

Plan your installation. You may wish to follow a different order of installation steps than is outlined
in this manual.

4.3.5.

The Installing Cables

Installing appropriate cables from location to location. Refer to the System Block Diagram in your
Antenna manual.

«
...
29
30
31
32
33
...
»

Содержание DAC-03

















































































Отзывы:

Нет отзывов

Похожие инструкции для DAC-03

Бренд: Manfrotto Страницы: 16

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Yamaha Страницы: 92

Бренд: Polycom Страницы: 2

Бренд: Baninni Страницы: 5

Бренд: DigiPower Страницы: 27

MT600iWP Series

Бренд: weintek Страницы: 2

Cutler-Hammer LMR

Бренд: Eaton Страницы: 38

Бренд: GI.BI.DI Страницы: 60

DuoControl Signal 111

Бренд: Tormatic Страницы: 3

Бренд: Procom Страницы: 10

Бренд: Velux Страницы: 11

Бренд: Kantronics Страницы: 201

CITY MICRO DOUBLE

Бренд: Baby Jogger Страницы: 9

External Joystick

Бренд: Quickie Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды