Sea Eagle FishSUP FS126 Скачать руководство пользователя страница 12

11

FishSUP | 

DEFLATION

To deflate, push down on 

the valve stem and  

quarter turn it to the 

right. The stem will stay 

in the down position, 

 allowing the air to escape. 

  

Warning: Air escapes 

with force, do not place 

face directly over valve.

Make the first fold over the motor mount. Tuck 

the rear tips under and bring skeg base on top.

Continue folding all the 

way to the bow, squeezing 

air out as you go.

Place the folded board in 

the backpack carry bag.

The FS126, pump, AB30 

kayak paddle, skegs, two 

rod holders and Fishing 

Rig frame (minus seat) are 

packed in this bag.

FishSUP | 

CLEANING & PROTECTING

Dry after each use to avoid mold. While washing or  

rinsing: close the valve and twist the cap on so water  

cannot not enter the chamber. Sea Eagles can be cleaned 

very effectively with general purpose cleaning products and a 

scrub brush. Towel dry.

Protection from the Sun and Heat

Avoid leaving the board in direct sunlight when ashore.  

Temperatures on a beach, dock, davit, etc. can get very high, 

which could affect the vinyl or glue. Excessive exposure to sun 

and heat can cause your Sea Eagle to become sticky or cause 

the glue to fail. 

 

Treat the board with a UV protectant such as 303 Aerospace 

Protectant. Generally, protectants are a thin film of oil, which 

will help keep your Sea Eagle clean. Avoid applying protectant 

on the EVA pad or places where foot traction is needed. 

Treated board will repel sand, water scum and tar stains.

FishSUP | 

STORAGE

If you’re planning to leave your Sea Eagle outside, keep it raised 

off the ground and covered so it is not exposed to sunlight, 

rain, leaves, berries, bird droppings, etc.  

 

Storage Tips: “

The best way to store a Sea Eagle is folded up in it’s  

bag”. 

- Cecil Hoge, Jr., Sea Eagle President 

 

• Check for water in the chambers. Water will leak out of open 

valves when it is rolled up.

• Water left inside can leak out and cause a lot of mold. Dry 

thoroughly to prevent mold.

• Rodent-proof the storage area. Mice, squirrels and other small 

rodents can do a lot of damage.

• Avoid excess heat. Do not store in direct sunlight, in an attic or 

a metal shed.

• In temperatures below freezing, do not drop, strike or  

Содержание FishSUP FS126






















Отзывы: