SDT Sherlog Kit Master SDT270 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 61

background image

File name: MAN.MAS.EN‐‐02X‐‐Sherlog‐Master‐user‐manual‐Eng.docx

33/60

12.4

Setting the transmitting power

When testing the tightness of volumes/holds, set the multi‐setting selector according to the volume of the space to
be tested.

For larger volumes/holds, the selector should normally be set on position 6. For smaller holds/volumes the selector may
have to be set to a lower position.

12.5

Measurements

The 8 transducers of the multi‐transmitter work in t h e bi‐sonic mode on frequencies stabilized at 39.2 and 39.6
kHz, with total transmission power also stabilized at 8 x 125 mW. The measurements will be carried out by the
SDT270

receiver (see chapter 15 for the use of the equipment).

12.6

Powering Off

To power off the transmitter, set the switch to the Off position (1). The red operating status light should switch off.

13

Charging the SDT 8 MS transmitter

battery pack

The battery packs are charged in our factory for test purposes but the battery packs are discharged before being
dispatched, because of international air transport regulations. Upon reception, the battery packs should be recharged.

Recommendations

The battery is a sealed lead‐acid gel battery. Therefore:

•

Short circuit of the contacts is dangerous.

•

The battery must not be discarded onto a flame.

•

Recharging in a sealed box is prohibited (gas leaks).

•

All mechanical shocks able to break the box may adversely affect the life of the battery.

•

In the case of electrolyte coming into contact with the skin, rinse the contaminated area immediately with water.

•

Recharge an unused battery pack every three (3) weeks.

Generalities on charging

Charging will be carried out:

•

Either to maintain the charge of the battery. A continuous charge is not harmful to the life of the battery, as
long as the charger provided with the multi‐transmitter is used.

•

Or after the flashing of the indicator of the battery.

The following table details the state of battery charge in relation to the information provided by the indicator:

Power
switch

Indicator

light

Transmitter

On

Continuous

-

Transmitter is switched on.

-

Battery charge is correct.

On

Flashing

-

Transmitter is switched on.

-

Battery charge is incorrect.

-

The speed of the flashing increases as the charge decreases.

On

Off (no light)

Insufficient charge, or no battery.

Off

Transmitter is switched off.

«
...
31
32
33
34
35
...
»

Содержание Sherlog Kit Master SDT270






























































Отзывы:

Нет отзывов

Похожие инструкции для Sherlog Kit Master SDT270

Бренд: Yamaha Страницы: 2

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: SOMFY Страницы: 40

Бренд: SAT-Kabel Страницы: 12

Бренд: Fora Страницы: 64

Бренд: Bogen Страницы: 14

Бренд: Kurzweil Страницы: 12

Бренд: MRC Страницы: 14

Бренд: Tonghui Страницы: 65

Бренд: Milkotester Страницы: 44

Бренд: Vanguard Instruments Страницы: 85

Бренд: Hanna Instruments Страницы: 11

Бренд: Kawai Страницы: 36

Бренд: Cable Detection Страницы: 2

INUKTUN MINIMAG

Бренд: Eddyfi Technologies Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды