SDLG WP6 Скачать руководство пользователя страница 89

Страница: 89 / 121

Service Manual for WP6 Diesel Engine

(8)

Remove engine front cover, refer to disassembly of engine front cover for details.

(9)

Remove injection pump module, refer to disassembly of injection pump for details.

3713

Steps to Assemble Fuel System

Assembling steps are contrary to disassembling ones.

372

Disassembly, Inspection, Maintenance and Assembly of Fuel Injection

Pump

3721

Exploded View of Fuel Injection Pump

Injector

Injector fuel return pipe

Fine fuel filter

Fine fuel filter support

Low pressure fuel pipe

High pressure fuel pipe

Injection pump

Coarse fuel filter

Coarse fuel filter support

Smoke limiter

Low pressure fuel pipe

Injection pump gear

Engine front cover plate

Injection pump lubricating pipe

Fig. 3-46 Exploded view of fuel injection pump

3722

Steps to Disassemble Fuel Injection Pump

(1)

Disconnect all external pipes and wiring harnesses of fuel injection pump.

(2)

Remove the hollow bolts that connecting fuel injection pump and low pressure fuel pipe.

(3)

Remove the hollow bolts that connecting fuel injection pump and smoke limiter air pipe.

(4)

Remove the hollow bolts that connecting fuel injection pump and injector fuel return pipe.

(5)

Remove the connecting nuts that connecting fuel injection pump and high pressure fuel pipe.

Содержание WP6


























































































































Результаты поиска

Содержание WP6

Отзывы:

Похожие инструкции для WP6

Бренды по названию

Популярные бренды

SDLG WP6, Руководство по обслуживанию

Результаты поиска

Содержание WP6

Отзывы:

Похожие инструкции для WP6

Бренды по названию

Популярные бренды