SDLG LG958L страница 76 Скачать руководство пользователя

Страница: 76 / 128

Operation & Maintenance Manual

──

LG958L/LG959 Wheel Loader

Operating methods

a) Refrigeration

Start the engine.

Open the air volume and power switch 2 which have three gears (fan low gear, fan middle

gear and fan high gear) and four positions (O, L, M and H). The speed of evaporating fan

increases from left to right to adjust the air volume.

Open the temperature control switch 3 to the max (the indicator lamp 1 will light), then the

compressor starts working for the refrigeration of air conditioning.

Turn the air volume and power switch 2 to select different gear to obtain three different

volume of air.

Turn the temperature control switch anticlockwise slowly to obtain the desired temperature

until the indicator lamp 1 turns off and the compressor stops working. Now the setting

temperature is the temperature in the cab. When the inside temperature is higher than the

setting temperature, the indicator lamp 1 lightens and the compressor will begin to refrigerate;

when the inside temperature is lower than the setting temperature, the indicator lamp 1 turns

off and the compressor stops working.

b) Heating

Before using, turn the temperature control switch to the ‘O’ position (the state of off).

Open the hot water valve and start engine.

Open the air volume and power switch 2 to choose the position of gear and adjust to the desired

air volume.

1.2.9.1 control panel

Ⅱ

and its operation (if assembled)

The Appearance of Panel

Содержание LG958L

































































































































Результаты поиска

Содержание LG958L

Отзывы:

Похожие инструкции для LG958L

Бренды по названию

Популярные бренды

SDLG LG958L, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LG958L

Отзывы:

Похожие инструкции для LG958L

Бренды по названию

Популярные бренды