background image

Select Keypad Active Output

 Default:  No Output

Sets which output activates when any keys are pressed.  This 
output is timed.  If toggle mode is selected for the output, the timer 
value defaults to 2 seconds.

Press: 14 # 

Output

 

 #  

Output=Output to Activate(0-4)

1=Main Relay;  2=Auxiliary Relay;  3=Output #3;  4=Output #4; 

0=No Output

Select Keypad Lockout Output

           Default:  No Output

Sets which output activates when the keypad is “locked out” after 
too many incorrect entry code attempts. The lockout time is 60 
seconds.

Press: 13

 

 # 

Output

 

 #  

Output=Output to Activate (0-4)

1=Main Relay;  2 = Auxiliary Relay;  3=Output #3; 4=Output #4;  

0=No Output / Lockout Disable

Select Alarm Shunt Output

 Default:  No Output

Sets which output activates during the time access is granted.  
(Use this output ot shunt alarm contacts attached to the access 
door.)  This output may be timed or toggled.

Press: 15 # 

Output

 

 #  

Output=Output to Activate(0-4)

1=Main Relay;  2=Auxiliary Relay;  3=Output #3;  4=Output #4; 

0=No Output

Select Request-to-Exit Output

 

Default:  No Output

Sets which output activates when the Request-to-Exit input is 
grounded.  This output may be timed or toggled.

Press: 16 # 

Output

 

 #  

Output=Output to Activate(0-4)

1=Main Relay;  2=Auxiliary Relay;  3=Output #3;  4=Output #4; 

0=No Output

Main Relay On-time

 

Default:  02 Seconds

Sets the length of time the Main Relay activates when triggered.

Green LED is on when Main Relay is active.

Press: 21 # 

Seconds

 

 #  

Seconds=Output time in seconds (0-60)

Auxiliary Relay On-time

               Default:  02 Seconds

Sets the length of time the Auxiliary Relay activates when triggered.

Press: 22 # 

Seconds

 

 #  

Seconds=Output time in seconds (0-60)

Anti-Tamper Output

 

               Default:  No Output

Sets which output activates when the Anti Tamper switch on the 
back of the keypad is activated. 

Press: 17 # 

Output

 

 #  

Output=Output to Activate(0-4)

0=No Output;  2=Auxiliary Relay;  3=Output #3;  4=Output #4;  

P:\INST INSTRUCTIONS\ACCESS CONTROLS\INST-923P       Rev H       08-21       Page 5

Erasing All Entry Codes

WARNING:  PERFORMING THIS COMMAND WILL REMOVE 

ALL ENTRY CODES FROM THE MEMORY

Press: 97 # 0 0 0 0 0 0

 

 #  0 0 0 0 0 0

 

 #  

  

Note: 

The green indicator will light while the memory is being 

erased.  This may take up to 15 seconds.

SECURITY DOOR CONTROLS   ■   WWW.SDCSECURITY.COM

[t] 800.413.8783  ■  805.494.0622  ■  E-mail: [email protected]  ■  801 Avenida Acaso, Camarillo, CA  93012  ■  PO Box 3670, Camarillo, CA  93011

Erasing Multiple Users (Sequential)

Press: 09 # 1

st

 

User

 

 # Number of users

 

 #  

1

st

 User =Starting user number to delete

Number of users = Total number of consecutive users  to delete

The yellow indicator will flash quickly while the 920P erases the 
users from  memory. The green indicator will light when the users 
are erased.

Erasing a Single User

Press: 02 # 

User

 

 #  

User

 

 #  

User =The user number to delete  001-500

The green indicator will light when the user is erased.

Configure Sense Input                                   Default:  INHIBIT 

  

The Sense Input (gray wire) can be programmed for either 
DOOR SENSE or INHIBIT.

Press:  10 # Input #

Input=0 for Door Sense; =1 for Inhibit

When programmed for DOOR SENSE, if an open condition on 
the input occurs before access is granted (with an entry code or 
with the request-to-enter input) a FORCED ENTRY output will 
occur.  If an open condition remains beyond the door ajar time 
following an access grant, a DOOR AJAR output will occur.
 
When programmed for INHIBIT, a closed condition on the input 
will prevent Relay #1 from activating when access is requested 
with an entry code.  This mode is typically used with an external 
timer to disable the access device at certain times.

Select Forced Entry Output

           Default:  No Output

  

Sets which output activates if the DOOR SENSE input opens 
before access is granted.  The output is not timed.  The selected 
relay latches ON, until any valid code (timed or toggled) is 
entered. 

Press:  11 # Output #

Output=Output to Activate(0, 2-4)

2=Auxiliary Relay;  3=Output #3;  4=Output #4;  0=No Output

Select Door Ajar Output

           Default:  No Output

  

Sets which output activates if the DOOR SENSE input stays open 
beyond the door ajar time after access is granted (door ajar time 
is adjustable using Function 25).  This output is not timed.  When 
the DOOR SENSE input returns to normal, the output turns off.

Press:  12 # Output #

Output=Output to Activate (0, 2-4)

2=Auxiliary Relay;  3=Output #3;  4=Output #4;  0=No Output

Содержание EntryCheck 923P









Отзывы: