background image

Galaxy 5000RS-2W Plus  -  Page 17

S

Sy

ys

stte

em

m W

Wiirriin

ng

g

6-Pin Starter Harness

Pin 1

RED WIRE A

: Main Power Input A (+). Connect to the battery or constant power wire at the ignition

switch with a minimum 30 Amp supply. Remove the fuse until the installation is complete and all wiring
is checked. 

Pin 2

RED WIRE B

: Main Power Input B (+). Connect to the battery or constant power wire at the ignition

switch  with  a  minimum  30  Amp  supply.    Note:  if  connecting  at  the  ignition  switch  it  is  highly
recommended  to  use  separate  power  wires  for  each  Red  wire,  each  with  a  minimum  30A  supply.
Remove the fuse until the installation is completed and all wiring is checked. 

Pin 3

BROWN WIRE

: Second Ignition  Output  (+).  The  Brown  wire pr12V for  a  second  ignition

wire. This wire may instead be programmed for use as a second accessory or second starter wire.

Pin 4

ORANGE  WIRE

:  Accessory  Output  (+).    Connect  to  the  accessory  wire  coming  from  the  ignition

switch that supplies power to the heater/air-conditioner.  Some cars may have multiple accessory wires. 

Pin 5

YELLOW WIRE

: Ignition Output (+).  Connect to the main ignition wire that pr12V when the

ignition is on and while cranking the starter. 

Pin 6

VIOLET WIRE

: Starter Output (+). Connect to the the vehicle’s starter wire.

20-Pin Main Harness

Pin 1

GREEN/WHITE WIRE

: Brake Input (+).  Connect to the wire that shows +12V when pressing the

brake.  The Green/white wire is a safety shutdown wire that must be connected.

Pin 2

BLACK/GRAY  WIRE

:  Tach  Input.  Connect  to  the  vehicle’s  tach  wire  or  a  fuel  injector  wire  if  the

tachless mode does not provide satisfactory operation.

Pin 3

WHITE/RED WIRE

: Auxiliary 2 Output (-) 500 mA. Connect to a relay or module for an optional

feature such as power window activation, etc. This output may be programmed for momentary, timed,
or latched operation.

Pin 4

BLACK/WHITE  WIRE

:  Dome  Light  Output  (-)  500  mA.  Connect  to  the  wire  that  activates  the

vehicle’s dome light, usually the door pin switch wire. NOTE: The dome light output can usually connect
to the same wire used for the door trigger input (see Green and Violet door trigger wires).

Pin 5

YELLOW WIRE

: +12V Ignition Input.  The Yellow wire must connect to a main ignition wire at the

ignition harness. This wire must show +12V when the ignition is on and while cranking the starter. The
voltage must not drop when the car is starting.

Pin 6

BLUE/YELLOW  WIRE

:  Glow  Plug  Input  (+).    For  vehicles  equipped  with  diesel  engines  the

Blue/yellow wire must be connected to the wait-to-start light in the gauge panel.  This wire will show
+12V when the light is on, and ground when the light turns off.  If the wait-to-start wire shows ground
when the light is on, a relay must be installed (see wiring diagrams).

Pin 7

BLUE/WHITE  WIRE

:  Passenger  Unlock  Output  (-)  500  mA.  Connect  to  a  relay  to  unlock  the

passenger doors when the system is configured for Driver Priority Unlocking. 

Pin 8

BLUE/ORANGE WIRE

: Ground When Running Output (-) 500 mA. Connect to an optional factory

security bypass module if required. 

Pin 9

BLACK WIRE

: Ground Input (-). The Black wire must connect to a solid chassis ground. Clean away

any paint or dirt to insure the best possible ground.   

Pin 10

RED WIRE

: Module Power Input (+). Connect to a constant source of +12V.

Pin 11

VIOLET WIRE

: Positive Door Input (+).  Connect to the door switch circuit wire that shows +12V

Содержание 5000RS-2W





































Отзывы: