manualshive.com logo in svg

Scranton Products Duralife Lockers, Руководство по установке, Страница: 23 / 24

Поделиться
Скачать
Scranton Products Duralife Lockers Скачать руководство пользователя страница 23

 

 23 

SECTION 12. ADA Kit 

(cont.)  

Please validate all local, municipal, state and federal codes before installation.  Below are noted reach 
ranges from current building codes.  

4.2.6 Side Reach. If the clear floor space allows parallel approach by a person in a wheelchair, the     
maximum high side reach allowed shall be 54 inches and the low side reach shall be no less than 9   
inches above the floor.  

308.2.1 Forward Reach Unobstructed. Where a forward reach is unobstructed, the high forward reach 
shall be 48 inches maximum and the low forward reach shall be 15 inches minimum above the finished 
floor or ground.  

 

Children Reach Ranges:  

Forward or Side Reach 

Ages 3 and 4               Ages 5 through 8 

             Ages 9 through 12  

High (Max) 

 

 

  36 inches   

      40 inches  

 

        44 inches 

Low (Max)  

 

 

  20 inches   

      18 inches   

 

        16 inches  

Mark the inside of the locker for the clip locations and pre-drill 
using a 15/64” drill bit. Drill straight and do not drill at an angle, 
walk the drill, or allow it to wobble.  

Doing so may result in a loose clip.  

 

If drilled properly the clips will fit snug. Push the clips in snug 
and place the shelf on top.  

Содержание Duralife Lockers

























Отзывы:

Нет отзывов