Scranton Products Duralife Lockers Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 24

Scranton Products Duralife Lockers Скачать руководство пользователя страница 18

18

SECTION 9. Slope Tops

(cont.)

Slope Top Installation: (Island)

The first step when installing slope tops in an Island is to fasten the rear supports together using the
1-1/2” torx head fasteners provided.

Once the rear supports are fastened together begin setting them into position.

Pre-drill from inside the cabinet to the under side of the combined 1” rear supports.

Next fasten from the inside of the cabinet using the 1-1/2” torx head fasteners provided.

Next take the slope top with the rounded edge to sit in front of the lockers.

Pre-drill holes and fasten slope top at locker front with #8-1” screws 3/4” from each joint and then every
24” on center. For a secure installation, use the #8-1” screws provided to fasten the slope top to the rear
support (optional). For a clean look, do not fasten the slope top to the rear support.

Slope Tops are provided in full length runs. The adjacent Slope Tops will butt up against each other.

Refer to illustration A. Slope Top Install on page 15

3/4” from joint

24” on center

«
...
16
17
18
19
20
...
»

Содержание Duralife Lockers

























Отзывы:

Нет отзывов