TO TURN THE TOOL ON
Slide on/off switch forward as shown in Fig.1. To turn the tool
OFF, slide switch back as shown in Fig
2.
WARNING:
Do Not use the blower with any type of accessory or
attachment. Such usage might be hazardous.
BLOWING
Blower can be used to clean corners,
fences, walls, wooden areas or beneath
cars. Be careful how you point the jet of air
as it could move heavy material and cause
injury or damage.
Turn the switch to on, point the jet of air in
front of you and move forward slowly to
gather together the leaves or to move the leaves from inaccessible
areas.
Avoid collisions with hard objects which could damage your
blower.
Keep bystanders and animals at least 5 m (15 feet) away from the
working area.
OPERATING
MAINTENANCE
If you drop the blower, carefully inspect it for damage. If the tube is
broken, housing cracked, or handles broken or if you see any
other condition that may affect the blower’s operation, call our
customer service help line at 1-800-618-7474
for assistance.
To clean the tool, make sure the battery is detached from the unit,
then use only mild soap and a damp cloth. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT
: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed by an
authorized service center or other qualified service organization,
always using identical replacement parts.
CAUTION:
Do not at any time let brake fluids, gasoline,
petroleum based products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can damage,
weaken or destroy plastic.
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals Do not store the tool
on or adjacent to fertilizers or chemicals.
CALL US FIRST !!
Call us first with questions about operating or maintaining your cordless
blower at 1.800.618.7474
between 8:00 a.m. – 5:00 p.m. Eastern
Standard Time, or get assistance on scotts.americanlawnmower.com.
4
LB23020S
TROUBLESHOOTING
Problem
-
Unit does not run
Possible Cause
- Battery not making contact
- Battery not installed properly
- Battery not charged
Possible Solution
- Check battery is fully inserted
- Check that battery is securely connected to the blower
- Check battery charging requirements
- Battery will not charge
- Battery not inserted into charger
- Charger not plugged in
- Surrounding air temperature too hot or too cold
- Insert battery into charger until red LED appears
- Plug charger into a working outlet
- Check current at receptacle by plugging in a lamp or other appliance
- Check to see if receptacle is connected to a light switch which turns
power off when you turn out the lights
- Move charger and tool to a surrounding air temperature of above 39
degree F (4 degree C) or below 104 degree F (40 degree C)
Make sure that the switch is in “OFF” position, the battery pack is
disconnected and all the rotating parts are at a standstill before
cleaning, carrying out inspections or moving from one place to
another.
Do not put part of your body such as hands and fingers in the
exhaust opening.
Do not switch the machine on in enclosed or poorly ventilated
spaces or in the presence of flammable and/or explosive
substances such as liquids, gas and powders.
WARNING:
After battery has been fully depleted, make sure switch
is in the “OFF” position.
POWER
BOOST
FEATURE
This
feature
is
located
on
tool
handle
as
shown
in
Fig
3
.
It
allows
you
to
optimize
the
tool
performance
and
boost
the
power
as
needed
.
Switch
the
blower
on
.
To
activate
the
“Boost”
mode, depress the
POWER
BOOST
button.
Operate
in
“
Normal
”
mode
for
most
blowing
needs
.(
Longer
runtime
will
be
achieved
.)
Activate
“
Boost
”
mode
as
needed
to
clear
heavy
or
wet
debris.
Fig
.
2
Fig
.
1
POWER
BOOST
Button
Fig
.
3
