manualshive.com logo in svg

Scotsman Prodigy Elite MC0322, Руководство по обслуживанию

Поделиться
Скачать
Scotsman Prodigy Elite MC0322 Скачать руководство пользователя страница 65

MC0322 through MC2148

Air, Water, and Remote Cooled Service Manual

January 2022 

Page 65

Repair Section

Purge valve

1. 

Push and hold the Off button to shut the machine off.

2.  Disconnect electrical power.

3.  Remove front panel.
4.  Remove left side panel.
5.  Unplug wires from valve coil.
Note: The coil can be removed from the valve body by rotating it 1/8 

turn CW. After removal of the coil the spring and plunger can be taken 

out.
6.  Remove screws holding valve to mounting bracket.
7.  Remove inlet and outlet hoses
8.  Remove valve from cabinet.
9.  Reverse to reassemble
10. Push and release the On button to restart the machine

Water level sensor

1. 

Push and hold the Off button until the machine shuts off.

2.  Remove the front panel.
3.  Locate water level sensor.
4.  Squeeze the locking tabs together and pull the sensor  

up and out of the sump.

5.  Unplug the electrical connection from the sensor.
6.  Reverse to reassemble

Electrical Shock Hazard
Disconnect electrical 

power before beginning

Содержание Prodigy Elite MC0322















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды