Scotsman Prodigy Elite MC0322 Скачать руководство пользователя страница 4

Страница: 4 / 110

January 2022

Page 4

MC0322 through MC2148

Air, Water, and Remote Cooled Service Manual

Water

The quality of the water supplied to the ice machine will have an impact on the time between cleanings and

ultimately on the life of the product. There are two ways water can contain impurities: in suspension or in

solution. Suspended solids can be filtered out. In solution or dissolved solids cannot be filtered, they must be

diluted or treated. Water filters are recommended to remove suspended solids. Some filters have treatment in

them for suspended solids. Check with a water treatment service for a recommendation.
RO water. This machine can be supplied with Reverse Osmosis water, but the water conductivity must be no

less than 10 microSiemens/cm.

Potential for Airborne Contamination

Installing an ice machine near a source of yeast or similar material can result in the need for more frequent

sanitation cleanings due to the tendency of these materials to contaminate the machine. Most water filters

remove chlorine from the water supply to the machine which contributes to this situation. Testing has shown

that using a filter that does not remove chlorine, such as the Scotsman Aqua Patrol, will greatly improve this

situation, while the ice making process itself will remove the chlorine from the ice, resulting in no taste or odor

impact.
Additionally, devices intended to enhance ice machine sanitation, such as the Scotsman Aqua Bullet, can be

placed in the machine to keep it cleaner between manual cleanings.

Water Purge

Cube ice machines use more water than what ends up in the bin as ice. While most water is used during ice

making, a portion is designed to be drained out every cycle to reduce the amount of hard water scale in the

machine. That’s known as water purge, and an effective purge can increase the time between needed water

system cleaning.
In addition, this product has the capability to automatically vary the amount of water purged based on the purity

of the water supplied to it. The water purge rate can also be set manually. Adjustments of purge due to local

water conditions are not covered by warranty.

Содержание Prodigy Elite MC0322















































































































Результаты поиска

Содержание Prodigy Elite MC0322

Отзывы:

Бренды по названию

Популярные бренды

Scotsman Prodigy Elite MC0322, Руководство по обслуживанию

Результаты поиска

Содержание Prodigy Elite MC0322

Отзывы:

Бренды по названию

Популярные бренды