Scotsman Prodigy Elite MC0322 Скачать руководство пользователя страница 46

Страница: 46 / 110

MC0322 through MC2148

Air, Water, and Remote Cooled Service Manual

December 2015 Page 46

Test Procedures - Sensors

All electrical components in this ice machine can be diagnosed with a volt-ohmmeter.

Curtain Switch:

1. Test using the controller’s indicator lights. Observe SW1 and SW2. Open and close the curtain in question.

When the curtain is opened, the SW light will be ON. When the curtain gets to within a half inch of closing (at

the switch) the SW light will go OUT.
2. Test with an ohmmeter. Disconnect electrical power. Open the control box cover. Unplug the curtain switch

lead from the controller. Connect an ohmmeter to the leads of the switch. Open and close the curtain. When

the curtain is closed, the switch is closed and there will be continuity (5 ohms or less). When the curtain is

open, the switch is open and the circuit will be open.
3. Test the controller’s curtain switch circuit by jumping the connectors on J7 or J8 together. Reconnect

electrical power. When jumped, the matching SW light will go out. When unplugged or open, the SW light will

be ON. J8 is for the SW1 light.

Curtain Switch

Indicator Lights
Light is ON when

curtain is OPEN
Single curtain models

have one indicator

light ON all the time.

Содержание Prodigy Elite MC0322















































































































Результаты поиска

Содержание Prodigy Elite MC0322

Отзывы:

Бренды по названию

Популярные бренды

Scotsman Prodigy Elite MC0322, Руководство по обслуживанию

Результаты поиска

Содержание Prodigy Elite MC0322

Отзывы:

Бренды по названию

Популярные бренды