Scotsman NM1852R Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 37

background image

Water Level

1. Unplug “water sen” connector from control
board.
2. Plug “water sen” connector from Scotsman
tester into circuit board.

a. Move “water” switch on tester to No Water

position. The No Water light on the circuit board
should go ON. If not, replace the circuit board.

b. Move the “water” switch on the tester to the

Water position. The No Water light on the board
should go OFF. If not replace the circuit board. If
the light does go off, replace the water level sensor.
If the Bin Empty light is ON, wait 10-20 seconds for
the machine to start. The machine should start.

NM1852R

December 1992

Page 37

«
...
35
36
37

Содержание NM1852R






































Отзывы:

Нет отзывов

Похожие инструкции для NM1852R

Бренд: La San Marco Страницы: 24

Бренд: U-Line Страницы: 57

Бренд: Cascade Страницы: 4

ENFINIGY 53103-3

Бренд: Zwilling Страницы: 136

Бренд: Hamilton Beach Страницы: 36

Бренд: La Pavoni Страницы: 72

Бренд: HAEGER Страницы: 44

Бренд: iGenix Страницы: 12

Бренд: Bunn Страницы: 26

E98/A-2 Compact

Бренд: Faema Страницы: 44

Бренд: ZORA Страницы: 36

Бренд: Ice-Tech Страницы: 22

Бренд: La Pavoni Страницы: 18

Nespresso Vertuo Plus

Бренд: Krups Страницы: 28

Бренд: Frigomat Страницы: 97

Бренд: Hamilton Beach Страницы: 5

Бренд: Quick MILL Страницы: 12

Home Bakery Virtuoso BB-PAC20

Бренд: Zojirushi Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды