Scotsman F1222L Скачать руководство пользователя

Страница: 30 / 34

N0922L, N1322L, F1222L, F1522L

Remote Low Side Service Manual Includes Prodigy Plus

December 2014

Page 30

Repair Procedures: The Water Seal:

(Assuming all steps to remove the auger have been

performed.)

1. The gear motor/evaporator assembly will have to

be exposed.

2. Remove the 4 hex head cap screws holding the

evaporator to the gear motor assembly. Lift the

evaporator up and off of the gear motor.

3. Remove the snap ring or wire retainer from the

groove under the water seal.

4. Pull or drive out the lower half of the water seal.

Tip: Push one side of seal in so the seal is turned 90

degrees to the evaporator and pull it out.

To Replace the Water Seal:

1. Lubricate the water seal with a thin coating of food

grade grease or oil, and push the water seal into the

bottom of the evaporator slightly past the groove for

the snap ring.

2. Replace the snap ring and pull the water seal down

against it.

3. The part of the water seal that rotates with the

auger must also be replaced. Remove the old part

from the auger and clean the mounting area.

4. Place a small bead of food grade silastic sealant

(such as 732 RTV or Scotsman part number 19-0529-

01) on the area of the auger where the water seal is

to be mounted.

5. Carefully push the water seal (rubber side against

the auger shoulder and the silastic sealant).

Do not get any sealant onto the face of the seal.

6. Allow the auger and seal to air dry until the sealant

is dry on the surface.

7. If the original water seal was leaking, it would be a

good idea to inspect the interior of the gear motor.

Snap

Ring

Stationary Water

Seal Bottom

Sealant

Содержание F1222L



































Результаты поиска

Содержание F1222L

Отзывы:

Похожие инструкции для F1222L

Бренды по названию

Популярные бренды

Scotsman F1222L, Руководство по обслуживанию

Результаты поиска

Содержание F1222L

Отзывы:

Похожие инструкции для F1222L

Бренды по названию

Популярные бренды