manualshive.com logo in svg

Scotsman F1222L, Руководство по обслуживанию

Поделиться
Скачать
Scotsman F1222L Скачать руководство пользователя страница 20

N0922L, N1322L, F1222L, F1522L

Remote Low Side Service Manual Includes Prodigy Plus

December 2014

Page 20

How Ice Is Made

Refrigeration effect is applied to the water between 

the auger and the evaporator. When that water's 

temperature drops to its freezing point, ice crystals 

form throughout it. A continually rotating auger moves 

the ice up the evaporator tube. At this point the ice is 

a soft ribbon that fills the space between the auger 

and evaporator.

At the top of the evaporator tube, ice emerges from 

the water and is forced or extruded through relatively 

small openings. This has the effect of squeezing out 

excess water and compressing the ice together into a 

useable form.

Ice flowing up from the openings is forced to one side, 

breaking it into smaller lengths. An ice sweep moves 

them to the chute.

Flaked ice machines have 6 oblong and curved slots 

that ice flows from, and they produce a softer, wetter 

ice form.

Nugget ice machines have 16 round holes that form 

the nuggets, which is more heavily compressed and 

contains less water than freshly made flaked ice.

Cutaway View

of Bearing

Nugget or

Flaked Ice

Foam

Insulation

Refrigerated 

Tubing

Содержание F1222L



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды