Scotsman ECC1200 Series Скачать руководство пользователя страница 22

Страница: 22 / 31

EH330, EH430 E and ECC Condensing Unit

Remote Low Side Cuber User Manual

August 2017

Page 21

Operational Characteristics 1200 lb system

Cycle Times @ Condenser Temp/Cabinet Temp/Water Temp in degrees F.

70/70/50

90/90/70

120/110/100

Freeze

9 to 11 minutes

12 to 14 minutes

17 to 19 minutes

Harvest

1 to 1.5 minutes

.5 to 1 minute

System Pressures @ Condenser Temp/Cabinet Temp/Water Temp in degrees F

70/70/50

90/90/70

120/110/100

Suction at head, end of Freeze 29 to 31 PSIG

34 to 36 PSIG

36 to 38 PSIG

Suction at head, Harvest - Peak 92 to 98 PSIG

165 PSIG

170 PSIG

Discharge at Condensing Unit:

Freeze - 5 minutes in

230 to 250 PSIG

250 to 270 PSIG

350 PSIG

Operational Characteristics 1400 lb system

Cycle Times @ Condenser Temp/Cabinet Temp/Water Temp in degrees F.

70/70/50

90/90/70

120/110/100

Freeze

10 to 14 minutes

13 to 17 minutes

21 to 25 minutes

Harvest

1 to 1.5 minutes

.5 to 1 minute

System Pressures @ Condenser Temp/Cabinet Temp/Water Temp in degrees F

70/70/50

90/90/70

120/110/100

Suction at head, end of Freeze 35 to 45 PSIG

35 to 45 PSIG

40 to 50 PSIG

Suction at head, Harvest - Peak 85 to 105 PSIG

100 to 120 PSIG

120 to 150 PSIG

Discharge at Condensing Unit:

Freeze - 5 minutes in

220 to 260 PSIG

250 to 270 PSIG

370 to 380 PSIG

Below information applies to both size systems:

Headmaster maintains a minimum discharge pressure during freeze of 217 PSIG + 25, -15 PSIG.

CPR Valve Setting: 55 - 60 PSIG.

Note: CPR allows a maximum low side pressure at the compressor. Maximum only occurs during harvest.

Refrigerant Charge

• 1200 - 24 oz.; 1400 - 224 oz,

Compressor Amps 1200

• Single Phase - 10 to 14

Compressor Amps, 1400

• Single Phase - 8 to 12
• Three Phase - 6 to 10

Batch Weight: 1200 - 10 lb
Batch Weight - 1400 - 14 lb
Discharge Pressure Cut Out Switch

• Cuts Out at: 450 PSIG Resets at: 350 PSIG

Содержание ECC1200 Series
































Результаты поиска

Содержание ECC1200 Series

Отзывы:

Похожие инструкции для ECC1200 Series

Бренды по названию

Популярные бренды

Scotsman ECC1200 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ECC1200 Series

Отзывы:

Похожие инструкции для ECC1200 Series

Бренды по названию

Популярные бренды