Scotsman CS0415 Скачать руководство пользователя

Страница: 18 / 26

Service Diagnosis

July 2007

Page 18

CS0415

Service Manual

Symptom

Possible Cause

Probable Correction

Will not make ice. Water
reservoir is full. Evaporator is
cold with thin/partial/irregular or
no ice slab

Seeping water valve. Condenser
is hot

Replace water valve

Partial refrigerant leak or
restriction (U-shaped slab)

Check for leak/restriction and
repair or replace defective
component

Defective recirculating pump

Repair or replace the pump
motor assembly

Partially blocked water distributor Clean distributor and evaporator

Will not make ice. Water
reservoir is full. Evaporator is
warm.

Compressor is not running

Test compressor, relay and
overload

Blocked condenser or stalled fan
motor

Clean condenser, repair or
replace motor

Unit is in the startup mode

Wait 5 minutes and recheck

Low capacity

Room temperature below 55

(13

Bin thermistor has unit shut off.
Advise user.

Seeping water valve. Condenser
is hot

Replace water valve

Slow or defective drain or drain
pump causing water to back up
into the bin

Repair or replace drain or drain
pump

Airflow blocked

Remove blockage

Control in extended cycle mode

Go to manual test 9, if clean light
is blinking, push Clean button
once.

Too much ice in bin

Defective bin thermistor

Test and replace thermistor

Noise

Banging sound

The slab dropping off the plate
and ice dropping from the cutter
grid into an empty bin are normal
sounds

Grinding, cavitating sound.

The reservoir is empty. Look for
a partially released slab,

interference with cutter grid etc
and clean the evaporator plate.

Grinding, cavitating sound from

recirculating pump

If the reservoir is full replace the
pump

Noisy drain pump

Repair or replace

Ice freezing together in the bin

Normal if little ice is used.

Use more ice.

Содержание CS0415



























Результаты поиска

Содержание CS0415

Отзывы:

Похожие инструкции для CS0415

Бренды по названию

Популярные бренды

Scotsman CS0415, Руководство по обслуживанию

Результаты поиска

Содержание CS0415

Отзывы:

Похожие инструкции для CS0415

Бренды по названию

Популярные бренды