Scotsman CME1386 страница 43 Скачать руководство пользователя | Manualshive

Страница: 43 / 46

background image

Controller Features & Last Error Recall

Last Error/Diagnostic Light Recall

To recall the last error on the blue housing CM

3

controller:

1. Switch the unit OFF by holding the OFF button
for longer than 3 seconds.

2. Hold the Off button down again until the Purge
Setting indicators (Green Lights) are on.

3. Push and release the Harvest button.

The last error code stored in the controller will be
displayed and the purge setting will disappear.

Push the Harvest button again and the
second-to-last error code will be displayed. The bin
full light will also be on to signal that this is the
second-to-last code.

Pushing the Harvest button again will display the
last error code again. Only two error codes are
available for display.

If no error code exists, no code will be displayed
and there will be NO LIGHTS showing.

To return from the display of the last error, do
nothing for 60 seconds or push and hold the Off
button.

After returning from the display of the last error (Off
light glows), the machine may be returned to the
ice making process by pushing and releasing the
Freeze button.

Controller Diagnostic Codes

If a Diagnostic
Light

Water Light

Refrigeration
Light

Blinks once and
repeats

Water pump will
not start

Very long ice
harvest

Blinks twice and
repeats

Lack of water fill

No harvest of ice

Blinks three
times and
repeats

not used

High discharge
temperature

Is ON all the time Water valve

leaking thru
rapidly

Maximum freeze
time

Both ON all the
time

Check for thermistor set unplugged
or failed

Program ID

The blue housing controller will display a code at
power up that indicates which ice machine model it
has been programmed for.

The code is based on the green lights that are
displayed.

1. At power up all lights flash ON once to indicate
that the controller has passed its internal
self-checks.

2. Immediately after that the program code will be
displayed for 20 seconds or until a button is
pushed.

Note: The

proper

program code for this machine is

glowing

·

CME1386: Bin Full and Freeze

·

CME1686: Bin Full, Freeze and Clean

Do NOT operate this machine if the wrong code is
displayed.

3. If no button is pushed after 20 seconds the
machine will display the Off light and is ready for
switch inputs (push and release Freeze to start
making ice).

Note: The Red Diagnostic Lights will be
FLASHING while the program ID is displayed.

Eclipse

ä

1300,1600

September 2003

Page 43

«
...
41
42
43
44
45
...
»

Содержание CME1386















































Отзывы:

Нет отзывов

Похожие инструкции для CME1386

Бренд: UFESA Страницы: 27

Бренд: BALAY Страницы: 2

Бренд: Elite Products Страницы: 4

Бренд: Clatronic Страницы: 50

Бренд: AGA marvel Страницы: 32

Бренд: Kalorik Страницы: 24

Бренд: Blueair Страницы: 36

Бренд: ENKHO Страницы: 50

Бренд: Ice Cream Depot Страницы: 12

Бренд: Villaware Страницы: 8

Бренд: TREVIDEA Страницы: 24

Бренд: Petra Страницы: 12

Бренд: Kompernass Страницы: 20

firma LF 400 MILK

Бренд: LAVAZZA Страницы: 104

Бренд: Gaggenau Страницы: 28

Бренд: Melissa Страницы: 37

WOLFGANG PUCK BICM0015

Бренд: Wolfgang Puck Страницы: 16

Бренд: Scotsman Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды