Read pages
1985-88 Chevrolet Nova
3-7 for kit
assembly.
Radio Removal:
1. Remove the ashtray and extract the two screws from the ashtray bracket. Then remove the bracket.
2. Extract the two screws from the top edge of the radio trim panel, pull the trim out and remove the panel.
3. Remove the four screws which secure the radio to the dash, slide the radio out of the dash cavity,
disconnect the wiring harnesses and remove the radio.
4. Remove the two hex nuts from the factory radio mounting bracket, one from each side of the radio, and
remove the bracket from the radio.
RIGHT
LEFT
LADO DERECHO
"A1" BRACKET USE HOLE #4
LADO IZQUIERDA
"B1" BRACKET USE HOLE #2
"A1" SOPORTE USA ABERTURA NO. 4
"B1" SOPORTE USA ABERTURA NO. 2
8
7
7
7
"C2" BRACKET USE HOLE #4
"B2" BRACKET USE HOLE #3
FRONT OF KIT
"C2" SOPORTE USA ABERTURA NO. 4
"B2" SOPORTE USA ABERTURA NO. 3
FRENTE DE ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1998-01 Chevrolet S-10 Blazer
3-7 for kit
assembly.
1998-01 Chevrolet S-10 Pickup
1998-01 GMC S-15 Jimmy
1998-01 GMC Sonoma Pickup
1998-00 Isuzu Hombre Pickup
Radio Removal:
1. Extract the (2) screws securing the top area of the driver's side underdash
cover panel.
2. Pull the driver's side underdash down to access and extract (2) 7mm hex
screws holding the bottom of the dash bezel.
3. Extract the screw located in the top edge of the dash panel at the instrument cluster.
4. Carefully pry out on the dash bezel to release the fastening clips securing the bezel to the dash and
unplug headlight / misc. switches on the driver's (left) of the bezel.
CAUTION:
At this point, take care around the hazard switch, by tilting the wheel down and/or depressing the
switch so the panel will clear. Also take care to snap the passenger air bag switch from the dash panel and
push it back trhough its own hole rather than unplugging the switch. It is a costly repair bill in excess of $400
to replace the hazard switch.
5. Remove the dash bezel from the vehicle.
"B1" BRACKET USE HOLE #2
"A1" BRACKET USE HOLE #2
"B1" SOPORTE
"A1" SOPORTE
USA ABERTURA NO. 2
USA ABERTURA NO. 2
RIGHT SIDE
LEFT SIDE
LADO DERECHO
LADO IZQUIERDA
FRONT OF KIT
FRENTE DE ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
22
Read pages
1994-96 Pontiac Grand Prix
3-7 for kit
Radio Removal:
assembly.
1. Remove ash tray.
2. Extract two push pin style fasteners on the bottom side of the radio/dash/bezel where it curves under the
dash.
3. Carefully pry out on the dash trim to release two panel clips and remove the dash piece.
4. Extract two 7mm screws holding the factory radio, unplug connectors and antenna to remove radio.
"B1" BRACKET USE HOLE #2
"A1" BRACKET USE HOLE #2
"B1" SOPORTE USA ABERTURA NO. 2
"A1" SOPORTE USA
ABERTURA NO. 2
LEFT SIDE
RIGHT SIDE
FRONT OF KIT
LADO IZQUIERDA
FRENTE DE
LADO DERECHO
ESTUCHE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
Read pages
1992-93 Pontiac Grand Prix
3-7 for kit
assembly.
Radio Removal:
1. Extract the two screws securing the glove box door hinges and remove the door.
2. Extract the two screws securing the radio trim bezel on the passenger side.
3. Extract the three screws from the underside of the dash securing the under dash panel below the steering
column. Disconnect all the connectors and remove the panel.
4. Extract the two screws securing
the radio trim bezel on the driver’s
side and remove the bezel.
FLANGE NUT
TUERCO REBORDE
5. Remove the two nuts from the
TOP
TOPE
bottom of the radio cavity securing
the radio to the dash. Pull the radio
from the cavity, unplug the
connectors and remove the radio.
BOTTOM
FONDO
CARRIAGE BOLT
PERNO DE PORTE
USE THE SUPPLIED CARRIAGE BOLTS & NUTS TO MOUNT THE KIT PANEL TO THE SUB-DASH.
Usa los pernos de portey tuercos proveidos para montar la tablera estuche al tablero-sub.
Read pages
1995-99 Pontiac Sunfire/Convertible
3-7 for kit
assembly.
Radio Removal:
1. Open glovebox then remove two screws along the right side of the radio/heater trim bezel.
2. Carefully pull out on the right side of the radio/heater trim bezel and two alignment pins will release on the
driver’s steering column panel.
3. Remove radio/heater trim bezel.
4. Extract two screws holding radio, unplug and remove.
"B1" BRACKET USE HOLE #1
LEFT SIDE
RIGHT SIDE
"B1" SOPORTE
LADO IZQUIERDA
LADO DERECHO
USA ABERTURA NO. 1
"C2" BRACKET
USE HOLE #5
1
"C2" SOPORTE
USA ABERTURA NO. 5
FRONT OF KIT
2
FRENTE DE
TRIM BRACKET
ESTUCHE
CORTA EL SOPORTE
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
31
