background image

Standard Features 

 

½ mile 2-Way FM Transceiver 

 

 

Remote sensor control 

 

LCD Water proof / impact 
resistant remote 

 

 

Battery safeguard with “sleep 
mode”  

 

 

Ultra low power drain MCM 

 

 

Violation display with time stamp  

 

Built-in accelerometer 

 

 

Passive arming  

 

Ignition protection  

 

 

Selectable arming / disarming  

 

Range Confirmation Signal (RCS)  

 

 

Programmable multi-tone siren 

 

 

Remote panic feature 

 

Optional Accessories

 

 

Perimeter sensor (SN-5) – A miniature multi stage microwave sensor that detects motion 
in mass around the motorcycle. 

 

Ignition disable and anti-hijack kit (RID-5) - Allows remote disabling of the motorcycle’s 
electrical system, should someone force you off your bike. Also prevents the engine from 
being started when the system is armed. 

 

Back-up battery (BAT-5) – A built-in back-up battery feature allowing the siren and 
transmitter to continue operating when power is interrupted.
 

 

Factory Connector Kits–OEM style connectors that simply plug into the motorcycle’s 
factory wiring harness.  Connector kits are available for select motorcycle models. 

 

Table of Contents  

Installation 

 

Component List ---------------------------------------------------------------- 

Page 2 

 

Planning The Installation ---------------------------------------------------- 

Page 2 

 

Mounting The Components ----------------------------------------------- 

Page 3 

 

Color Codes --------------------------------------------------------------------- 

Page 3 

 

Connections --------------------------------------------------------------------- 

Page 4 

 

Using the T-tap Connectors ------------------------------------------------ 

Page 4 

User’s Guide 

 

Remote Transceiver Icons and Message Display ------------------- 

Page 5 

 

Turning Transceiver On / Off ----------------------------------------------- 

Page 5 

 

RCS (Range Conformation Signal) -------------------------------------- 

Page 6 

 

Transceiver Battery Status --------------------------------------------------- 

Page 6 

 

Operating Instructions ----- -------------------------------------------------- 

Page 6 

 

Alarm Triggers-------------------------------------------------------------------- 

Page 7 

 

Sensor Memory Display ------------------------------------------------------ 

Page 7 

 

Battery Safeguard with “Sleep Mode” -------------------------------- 

Page 7 

 

Motorcycle Battery Status -------------------------------------------------- 

Page 8 

 

Locking the Transceiver’s buttons --------------------------------------- 

Page 8 

 

Checking Motorcycle Status and Violation Display --------------- 

Page 8 

 

Programming and customizing  Instructions -------------------------- 

Page 9 

 

Selecting Transceiver Alert Type ------------------------------------------ 

Page 9 

 

Selecting Auto / Manual Arming ----------------------------------------- 

Page 10 

 

Selecting Siren Tone and Alarm Duration ----------------------------- 

Page 10 

 

Adjusting the Accelerometer (Shock / Tilt ) Sensor ---------------- 

Page 10 

 

Setting Clock Time ------------------------------------------------------------ 

Page 11 

 

Setting Alarm Clock ---------------------------------------------------------- 

Page 11 

 

Encoding a Transceiver ------------------------------------------------------ 

Page 11 

Optional Accessories Instructions 

 

Perimeter Sensor (SN-5) ------------------------------------------------------ 

Page 12 

 

Ignition Disable / Anti-hijack Unit ----------------------------------------- 

Page 13 

 

Back-up Battery ---------------------------------------------------------------- 

Page 14 

Warranty and FCC Information 

 

Limited Warranty  ------------------------------------------------------------- 

Page 15 

 

FCC Notice ---------------------------------------------------------------------- 

Page 15 

 

Contact information --------------------------------------------------------- 

Page 15 

Содержание SR-i500

















Отзывы: