(Planning the Installation cont)
1.
Check that your motorcycle battery is fully charged and that all electrical circuits are
in good working condition.
2.
Check the layout and construction of the motorcycle to decide what space is
available for the components.
3. Verify that no moving parts interfere with the components or the wires.
4. Do not route wires near sharp edges, which could cut wires and cause a short.
5. Do not mount components near extreme heat areas such as exhaust pipes
6. Allow at least an inch of slack at all connection points to reduce the chance of a
connection pulling apart due to vibration.
7. Do not drill any holes. Mount the components with the provided hook and loop
fasteners and cable ties.
Mounting the Components
Main Control Module
The MCM is equipped with three connectors. One is for the main harness (HAR-1), the
second is for the RFID antenna, and the third is for the optional accessories. Select a
suitable location under the seat or in a side cover. Mount the MCM using hook and loop
fasteners or cable ties. Make sure the unit is not easily accessible and is securely
attached.
Accessory Harness
Plug in the accessory harness to the matching connector on the MCM. Each one of the
connectors on the accessory harness is unique and can only be connected to the
correct accessory. Plug in the supplied dust cover if no accessories are installed.
Routing the RFID Antenna
Place the RFID module under the seat or in a plastic side cover. Do not choose a location
where the RFID signal will be blocked by metal. Mount the unit with the hook and loop
fasteners or cable ties. The signal range, depending on obstructions, is 2-3 feet.
Important
note: The RFID cable has three wires on one end and two wires on the other. Be
sure the end with 3 wires is connected to the MCM, and the end with 2 wires is
connected to the RFID antenna.
Routing the GPS Antenna
The GPS signal can transmit through fiberglass, leather and plastic, but not metal. Mount
the magnetic antenna on any flat surface, making sure that the top side of the sensor is
facing upwards.
Perimeter Sensor
The Perimeter Sensor signal can transmit through the seat, fiberglass, leather and plastic,
but not metal. Mount this unit on top of the battery or any flat surface, making sure that
the top side of the sensor is facing upwards. Mount the unit 6 to 8 inches away from the
MCM to ensure proper operation.
4
Main Harness
If the optional factory connector kit is being used, please disregard this section of the
instructions and refer to the instructions that were supplied with the factory connector kit
.
The main harness consists of two harnesses. One is labeled (HAR-1) and the second is
labeled (GEN-1). Plug in the white 4-pin connector from the (HAR-1) into the matching 4-
pin connector from the (GEN-1). The (HAR-1) also has a waterproof connector that plugs
into the MCM. The wires should be connected as follows:
HAR-1
Black wire with fuse and ring terminal – To battery Positive (+).
GEN-1
Black wire – To ground (-).
Grey wire – To turn signal power wire (Left).
Grey wire – To turn signal power wire (Right).
Orange wire – To license plate light power wire or tail light power wire OR any other wire
that is hot (+) when ignition is ON. DO NOT CONNECT TO BRAKE LIGHT. (NOTE: this is an
input to the alarm. This connection is not designed to flash the tail light).
Note: When the main harness (HAR-1) is plugged in, the siren will chirp (if equipped with optional
siren) and turn signals will flash twice. If the siren does not chirp, check the fuse, battery power (+)
and ground (-) connections.
If the turn signal lights do not flash, make sure that the grey wires are connected to the turn signal
power (+) wires. Connecting these wires incorrectly may damage the system.
Color Codes
(individual models may vary)
Ground (-)
Tail/License
Switched power
Left Turn Signal
power
Right Turn
Signal power
Honda
Green wire
Brown or
wht/blk stripe
Orange wire
Blue wire
Kawasaki
Black/yellow
Red wire
Green wire
Grey wire
Suzuki
Black/White
Brown wire
Green or Black
Grey wire
Yamaha
Black wire
Blue/red stripe
Green wire
Brown wire
Harley
Davidson
Black wire
Blue wire
Brown wire
Purple wire
Ducati
Black wire
Yellow wire
White/Black
White/Green
Fuse
To Battery (+)
HAR-1
GEN-1
Black – To Ground (-)
Grey – To Turn Signal
Grey – To Turn Signal
MCM Orange – To Tail Light
5
