background image

SCIFIT   •   Scientific Solutions for Fitness   •   SCIFIT   •   Scientific Solutions for Fitness   •   SCIFIT

The wireless heart rate transmitter strap accessory is a useful device 

if you desire continuous feedback on your current heart rate during a 

workout.

The Heart Rate Control program enables the user to set-up a target 

heart rate. Through real-time monitoring of the user’s heart rate, the 

console  maintains  the  user’s  heart  rate  at  or  below  this  established 

target rate by decreasing the elevation if the user’s heart rate exceeds 

the target.

To activate the HR Transmitter strap, follow the steps below:

1.   Unhook the strap by slightly twisting the snap button on either side 

outward until you can pull the button through the hole.

2.  Moisten the backside of the sensor, then adjust the strap below the 

pectoral muscle or breasts.

3.  Position  the  strap  so  that  the  transmitter  sensor  is  directly  in  the 

center of the chest as shown in the illustration.

4. The sensor will begin to monitor and transmit your heart rate.

NOTE: 

For best results place the transmitter under your garment, so it 

may contact the skin.

The transmitter is automatically turns off when it is removed.

Be  sure  to  wipe  the  strap  thoroughly  with  a  dry  cloth  after  each 

workout to ensure reliable operation.

Inaccurate  heart  rate  readings  may  occur  if  you  use  the  transmitter 

within an area near other sources of electromagnetic radiation.

Examples  of  such  sources  include:  other  fitness  equipment,  other 

heart rate transmitters, and televisions. To reduce erroneous readings, 

be sure to allow a minimum of 1 meter between each radiation source.

Never  use  the  Heart  Rate Transmitter  strap  if  you  wear  an  electrical 

heart  pacemaker  or  other  electrical  medical  device.  This  could  be 

extremely  dangerous  since  the  Heart  Rate Transmitter  can  interfere 

and cause electrical disturbances to those devices. 

The Contact heart rate is located directly in front of the user. Simply 

grip the contact grips lightly, after a short delay the pulse reading will 

appear on the display.

NOTE:

  If a transmitter heart strap is worn, this will over ride the reading 

of the contact heart rate.

Uses of the Heart Rate Transmitter Strap

Activating The Transmitter

De-activating the Transmitter

Signal Interference

Contact Heart Rate

Size Adjuster

Unhooking Strap

Snap Button

Snap Buttons

Transmitter 

Sensor

CAUTION:

 Users with Pacemakers

Heart Rate Transmitter Strap

5.1

CHR Grips

Содержание DC1000 Intelli-Fit

















































Отзывы: